Axles - Revision history

Wyldephyre: /* T-series Axles */

2005-05-22T00:02:42Z

T-series Axles

← Older revision		Revision as of 00:02, 22 May 2005
Line 3:		Line 3:
	[[Image:PICT2313-vi.jpg\|thumb\|From left to right: RA40, RA23, TA22]]		[[Image:PICT2313-vi.jpg\|thumb\|From left to right: RA40, RA23, TA22]]

	Lots of people talk about T-series diffs, kouki and zenki etc, but few people ever mention the axles. And then there's the people who say that if you have a non-LSD T-series diff and you want to put a TRD LSD center in, then you need to shorten the axles about 5mm...		Lots of people talk about T-series diffs, kouki and zenki etc, but few people ever mention the axles. And then there's the people who say that if you have a non-LSD T-series diff and you want to put a TRD LSD center in, then you need to shorten the axles about 5mm.

	Well anyways, what I wanted to point out is:		Well anyways, what I wanted to point out is:
Line 20:		Line 20:

	I'm not sure about the mounting plate, but visually they look the same. Splines are the same (obviously).		I'm not sure about the mounting plate, but visually they look the same. Splines are the same (obviously).

			<hr>
			[http://www.rollaclub.com/ Rollaclub]
			[[Category: Drivetrain]]

Demuire: /* T-series Axles */ Cleaned up

2005-05-20T23:21:29Z

T-series Axles: Cleaned up

← Older revision		Revision as of 23:21, 20 May 2005
Line 1:		Line 1:
	= T-series Axles =		= T-series Axles =

			[[Image:PICT2313-vi.jpg\|thumb\|From left to right: RA40, RA23, TA22]]

	Lots of people talk about T-series diffs, kouki and zenki etc, but few people ever mention the axles. And then there's the people who say that if you have a non-LSD T-series diff and you want to put a TRD LSD center in, then you need to shorten the axles about 5mm...		Lots of people talk about T-series diffs, kouki and zenki etc, but few people ever mention the axles. And then there's the people who say that if you have a non-LSD T-series diff and you want to put a TRD LSD center in, then you need to shorten the axles about 5mm...
Line 18:		Line 20:

	I'm not sure about the mounting plate, but visually they look the same. Splines are the same (obviously).		I'm not sure about the mounting plate, but visually they look the same. Splines are the same (obviously).

	~~[[Image:PICT2313-vi.jpg]]~~

	~~From left to right: RA40, RA23, TA22~~

Demuire: /* T-series Axles */ Fixed lists

2005-05-20T23:03:32Z

T-series Axles: Fixed lists

← Older revision		Revision as of 23:03, 20 May 2005
Line 7:		Line 7:
	Not all T-series axles are created equal. There are at least (and probably more) 3 different sorts:		Not all T-series axles are created equal. There are at least (and probably more) 3 different sorts:

	TA22: These are fairly short, fairly thin, and use tiny bearings		* TA22: These are fairly short, fairly thin, and use tiny bearings
	RA23/28, TA23: These are slightly longer than TA22, look to be a bit thicker, and use a much bigger bearing		* RA23/28, TA23: These are slightly longer than TA22, look to be a bit thicker, and use a much bigger bearing
	RA40/60: These are identical to RA23, except 30mm longer. Same bearing etc.		* RA40/60: These are identical to RA23, except 30mm longer. Same bearing etc.

	Measured with my dodgy tape measure, from axle flange to end:		Measured with my dodgy tape measure, from axle flange to end:

	TA22: 550mm		* TA22: 550mm
	RA23: 555mm		* RA23: 555mm
	RA40: 585mm		* RA40: 585mm

	I'm not sure about the mounting plate, but visually they look the same. Splines are the same (obviously).		I'm not sure about the mounting plate, but visually they look the same. Splines are the same (obviously).

Demuire: New page

2005-05-20T23:01:51Z

New page

New page

= T-series Axles =

Lots of people talk about T-series diffs, kouki and zenki etc, but few people ever mention the axles. And then there's the people who say that if you have a non-LSD T-series diff and you want to put a TRD LSD center in, then you need to shorten the axles about 5mm...

Well anyways, what I wanted to point out is:

Not all T-series axles are created equal. There are at least (and probably more) 3 different sorts:

TA22: These are fairly short, fairly thin, and use tiny bearings
RA23/28, TA23: These are slightly longer than TA22, look to be a bit thicker, and use a much bigger bearing
RA40/60: These are identical to RA23, except 30mm longer. Same bearing etc.

Measured with my dodgy tape measure, from axle flange to end:

TA22: 550mm
RA23: 555mm
RA40: 585mm

I'm not sure about the mounting plate, but visually they look the same. Splines are the same (obviously).

[[Image:PICT2313-vi.jpg]]

From left to right: RA40, RA23, TA22