Tech:Engine/K-Series/TRD: Difference between revisions

From Rollaclub
Jump to navigation Jump to search
No edit summary
Line 18: Line 18:
:Due to increase of compression ratio, the thickness upon assembling has been revised.
:Due to increase of compression ratio, the thickness upon assembling has been revised.
;b. Piston
;b. Piston
:Without altering the displacement (75Ø 1,166cc), the compression ratio has been incrased.
:Without altering the displacement (75∅ 1,166cc), the compression ratio has been incrased.
;c. Piston rings.
;c. Piston rings.


Line 27: Line 27:
====(2) Required parts.====
====(2) Required parts.====


{| class="wikitable"
{|
! Description !! Qty.
! Description !! Qty.
|-
|-
Line 48: Line 48:
|}
|}


{| class="wikitable" border="1"
!rowspan="3"|Item
!colspan="3"|Sports parts
!colspan="3"|S. T. D
|-
!colspan="2"|compression rings
!rowspan="2"|Oil ring
!colspan="2"|Compression rings
!rowspan="2"|Oil ring
|-
| No. 1 || No.2 || No.1 || No.2
|-
| Clearance between ring & ring groove (mm) || 0.02~0.04 || ← || 0.015~0.06 || 0.03~0.07 || 0.02~0.06 || 0.015~0.06
|-
| Gap clearance (mm) || 0.15~0.35 || ← || 0.20~0.90 || 0.15~0.35 || ← || 0.20~0.90
|}
==Stage II==
Besides the boring of the cylinder block and correction of the valve seats contacting surfaces, parts have been established which are capable for assembling almost without any modification.
===1. PISTON & PISTON RINGS===


====(1) Main modifications.====


;a. Piston


:The oversize is 3mm (78∅) with the displacement of 1,261 cc.
;b. Piston rings
:Two compression rings with the thickness of 1 mm are utilized.
:The oil ring is of three-piece type with the thickness of 2.5 mm.
====(2) Required parts.====
{|
! Description !! Qty.
|-
| Gasket,cylinder head || 1
|-
| Ring set, piston || 4
|-
| Piston w/pin || 4
|}
====(3) Assembling standards.====
{| class="wikitable"
! Item !! Sports parts !! S. T. D
|-
| Piston clearance mm || 0.07~0.10 || 0.03~0.05
|}


{| class="wikitable" border="1"
{| class="wikitable" border="1"
Line 69: Line 129:


| Gap clearance (mm) || 0.15~0.35 || ← || 0.20~0.90 || 0.15~0.35 || ← || 0.20~0.90
| Gap clearance (mm) || 0.15~0.35 || ← || 0.20~0.90 || 0.15~0.35 || ← || 0.20~0.90
|}
===2. VALVE MECHANISM===
====(1) Main modifications.====
;a. Camshaft
:The revise the valve timing, the cam profiles are revised.
;b. Valves
:To improve the intake and exhaust efficiency, the head diameters of the intake and exhaust valves have been enlarged.
;c. Valve springs.
:To prevent surging, revised from single to dual springs and the installed load is revised.
;d. Valve spring retainer & spring seat.
:Due to the revision of the valve springs from single to dual, the retainer and seat are newly established.
====(2) Required parts.====
{|
! No. !! Part No. !! Description !! Qty. !! Remarks
|-
| 1 || 13511-KE003 || Camshaft
!rowspan="2" Either one || Overlap 70°
|-
| || 13511-KE051 || Camshaft || Overlap 66°
|-
| 2 || 13711-KE051 | Valve, intake | 4 | Head dia. 37∅
|-
| 3 || 13715-KE051 | Valve, exhaust | 4 | Head dia. 30∅
|-
| 4 | 90501-42409 | Spring, compression (outer) | 8 | "O"
|}
|}




[[Category:K Motor]]
[[Category:K Motor]]

Revision as of 03:46, 16 September 2012

I'll let TRD do the talking!!!

http://www.vhtracing.com/TRD_K_ENGINE_MANUAL.pdf (Dead link)

http://www.rollaclub.com/hosted/TRD-K-Engine-Manual.pdf (Mirror, 25MB)

Link by Taz_Rx

Transcription

Stage I

Without altering the displacement (1,166 cc), the pistons have been established to increase the compression ratio.

Cylinder Head Gasket, Piston & Piston Rings

(1) Main modifications

a. Cylinder head gasket.
Due to increase of compression ratio, the thickness upon assembling has been revised.
b. Piston
Without altering the displacement (75∅ 1,166cc), the compression ratio has been incrased.
c. Piston rings.
Two compression rings with thickness of 1 mm are utilized and the oil ring is of three-piece type with the thickness of 2.5mm.


(2) Required parts.

Description Qty.
Gasket,cylinder head 1
Ring set, piston 4
Piston w/pin 4


(3) Assembling standards.

Item Sports parts S. T. D
Piston clearance mm 0.06~0.08 0.03~0.05
Item Sports parts S. T. D
compression rings Oil ring Compression rings Oil ring
No. 1 No.2 No.1 No.2
Clearance between ring & ring groove (mm) 0.02~0.04 ← 0.015~0.06 0.03~0.07 0.02~0.06 0.015~0.06
Gap clearance (mm) 0.15~0.35 ← 0.20~0.90 0.15~0.35 ← 0.20~0.90

Stage II

Besides the boring of the cylinder block and correction of the valve seats contacting surfaces, parts have been established which are capable for assembling almost without any modification.



1. PISTON & PISTON RINGS

(1) Main modifications.

a. Piston
The oversize is 3mm (78∅) with the displacement of 1,261 cc.
b. Piston rings
Two compression rings with the thickness of 1 mm are utilized.
The oil ring is of three-piece type with the thickness of 2.5 mm.



(2) Required parts.

Description Qty.
Gasket,cylinder head 1
Ring set, piston 4
Piston w/pin 4

(3) Assembling standards.

Item Sports parts S. T. D
Piston clearance mm 0.07~0.10 0.03~0.05
Item Sports parts S. T. D
compression rings Oil ring Compression rings Oil ring
No. 1 No.2 No.1 No.2
Clearance between ring & ring groove (mm) 0.02~0.04 ← 0.015~0.06 0.03~0.07 0.02~0.06 0.015~0.06
Gap clearance (mm) 0.15~0.35 ← 0.20~0.90 0.15~0.35 ← 0.20~0.90

2. VALVE MECHANISM

(1) Main modifications.

a. Camshaft
The revise the valve timing, the cam profiles are revised.
b. Valves
To improve the intake and exhaust efficiency, the head diameters of the intake and exhaust valves have been enlarged.
c. Valve springs.
To prevent surging, revised from single to dual springs and the installed load is revised.
d. Valve spring retainer & spring seat.
Due to the revision of the valve springs from single to dual, the retainer and seat are newly established.

(2) Required parts.

No. Part No. Description Qty. Remarks
1 13511-KE003 Camshaft rowspan="2" Either one Overlap 70°
13511-KE051 Camshaft Overlap 66°
2 Valve, intake | 4 | Head dia. 37∅
3 Valve, exhaust | 4 | Head dia. 30∅
90501-42409 | Spring, compression (outer) | 8 | "O"
Retrieved from "https://www.rollaclub.com/wiki/index.php?title=Tech:Engine/K-Series/TRD&oldid=4357"