Millaz88 Posted July 19, 2011 Report Posted July 19, 2011 Hey guys going to be pumping a small bit of boost into my 4k looked into what people have done and some guys are locking the dizzy and others are saying you must or you will blow head gaskets Soooooo what do you guys say? And what sort of timing should I go for? Also it's a 5k elec dizzy Cheers Miller Quote
Mitch-12 Posted July 19, 2011 Report Posted July 19, 2011 need to dyno it to know the timing and id lock it Quote
altezzaclub Posted July 19, 2011 Report Posted July 19, 2011 Soo... where do you lock it?? 8deg so it idles but doesn't rev? 15deg so it has a bit much advance for idling but has a good mid-range. 30deg? Hopeless at idle, much too advanced, but at least it runs up to 5000rpm because it has time to burn the mixture before the valves open. There's a lot to be said for the bright idea of ignition advance weights... I think you're up for a knock sensor, a big dyno run and a re-graph. Then it will fly! Quote
Mitch-12 Posted July 19, 2011 Report Posted July 19, 2011 to do it properly you need to dyno who knows how many degrees it needs you need to dyno it some people may disagree but i dyno everything before i race it and on the dyno you lose roller torque before it pings a good tuner will know all of this Quote
Millaz88 Posted July 19, 2011 Author Report Posted July 19, 2011 This supercharger is only on loan to me so there is no real point in getting it dyno tuned What if I block the vac advance? And leave the mechanical advance? I just don't want to blow hg's Quote
altezzaclub Posted July 19, 2011 Report Posted July 19, 2011 That's probably a good idea- Vac advance does advance faster, but obvously only on high inlet vacuum, or throttle off. So you get high advance on over-run, small throttle cruise and idle (if its inlet vac and not ported vac) Mechanical advance is pretty well straight with the revs, so you should pick the max advacne you want and set it to that at 3 or 4 thousand rpm, then use the idle speed to sort out the idle. Will superchargers run 36deg max advance? Quote
Mitch-12 Posted July 19, 2011 Report Posted July 19, 2011 does it fit the motor? like has it been made to fit a 4k, i don't know much about what your wanting to do. i say go for it but i can pretty much guarentee if you bolt a charger on guess the timing and drive you will blow a HG and what about the fuel? under boost it will be as lean as all hell but if it has a carb tuned for it or something then you should be sweet other wise it will prob melt a piston also Quote
Millaz88 Posted July 19, 2011 Author Report Posted July 19, 2011 I'm getting a complete kit that was made for another motor carby brakets and eveything bar dizzy so I'm thinking disconnect vac advance put timing back to 8* as it's up on 12* atm with 98 octain fuel I will be going to the dyno day in sep to get it tested that's y it's getting fitted to my car so I will have a tweak there I guess Thanks guys Quote
ke70dave Posted July 19, 2011 Report Posted July 19, 2011 depends how much you like electronics..... you could run the spark using a cheap ECU? an MS1 mega squirt is like $150 in kit for these days. figure out something for a Crank angle sensor (cheap cheap), then you can run whatever ignition curve you want. but getting the thing re graphed is probably the most sensible option.... Quote
Mitch-12 Posted July 19, 2011 Report Posted July 19, 2011 if its a full kit it should be easy how much boost does it make? Quote
Millaz88 Posted July 19, 2011 Author Report Posted July 19, 2011 depends how much you like electronics..... you could run the spark using a cheap ECU? an MS1 mega squirt is like $150 in kit for these days. figure out something for a Crank angle sensor (cheap cheap), then you can run whatever ignition curve you want. but getting the thing re graphed is probably the most sensible option.... I could deff wire one up I just thought they would be pretty pricy but thats cheap so it could be done The kit makes around 5psi I believe but yet to test on my car Quote
Mitch-12 Posted July 20, 2011 Report Posted July 20, 2011 if its inly 5 psi just take a few deg out ask taz_rx he had a carby with boost and knows roughly how much timing to pull out for how much boost Quote
kickn5k Posted July 20, 2011 Report Posted July 20, 2011 Will superchargers run 36deg max advance? No. The most I could ever get in mine was 28deg. Any more than that and it would not make more power. Any more than 31deg it rattled it head off Stu. Quote
Millaz88 Posted July 20, 2011 Author Report Posted July 20, 2011 No. The most I could ever get in mine was 28deg. Any more than that and it would not make more power. Any more than 31deg it rattled it head off Stu. So what should I do? Sounds like you have the know how Cheers Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.