August 1, 200719 yr Author comment_189813 Wow!!! What a tough little 25! :n: If you don't mind me asking, where did you source the U-bolts and backing plates from? Whiteline kit, which included 2" Lowering blocks and U bolts for a Corona or Sigma, can't remember which one. I had two kits for a while. I used the standard backing plates, and even though the lengths of the U Bolts are not exactly parallel, they are not too bad. I was able to bend the U Bolts by hand to make them fit the standard backing plates. Without the 2" spacer, they would be, in my opinion, too "unparallel." I think there is enough metal on the original backing plate to file away some metal, to get them exactly parallel. But you'll have to check that for yourself. Report
August 14, 200719 yr comment_191548 Question without notice! :wink: The hydraulic clutch: The Master is on the "wrong" side of the Brake master. Did you turn the clutch lever on the pedal box upside down(ish) and use it to lever that way? (If you know what I mean.) Just going through the process myself. Report
August 20, 200719 yr Author comment_192862 Question without notice! :P The hydraulic clutch: The Master is on the "wrong" side of the Brake master. Did you turn the clutch lever on the pedal box upside down(ish) and use it to lever that way? (If you know what I mean.) Just going through the process myself. Yep, that is what I did, sort of. The clutch "shaft" in the pedal box assembly is about 60mm long, so it is moved far enough over to miss the brake master cylinder. I actually replaced the small clutch lever (which is made for a cable) and put a bit of metal there, with a hole to accept the end of the master cylinder. From this hole to the pivot point, it is about 57mm. I might actually make it a bit longer, which will reduce the amount of pedal travel nneded, probably about 65mm. The possiton of the master cylinder (in my case) will accept this extra length. Report
August 21, 200719 yr comment_192924 very nice man, highly respectable. I have just completed a rebuild myself, not to your extent, but i am building a track car. Mods incl 20v 4AGE VVT 272deg cams surge tank fuel pump clutch Brake's cold air intake Soon to come will be. Motec ECU coilovers full exhaust. Does make some power, but in a fwd AE82 Rolla, its not what i'm after, long gears and wide torque is what i'm looking for, and i have seemed to acheive it. I'll post some pics later. Cheers mate, Report
August 22, 200719 yr comment_193273 very nice man, highly respectable. I have just completed a rebuild myself, not to your extent, but i am building a track car. Mods incl 20v 4AGE VVT 272deg cams surge tank fuel pump clutch Brake's cold air intake Soon to come will be. Motec ECU coilovers full exhaust. Does make some power, but in a fwd AE82 Rolla, its not what i'm after, long gears and wide torque is what i'm looking for, and i have seemed to acheive it. I'll post some pics later. Cheers mate, I'm curious as to what your psot has to do with his porject thread. Report
November 4, 200718 yr Author comment_207099 Well, the project is now registered, and a blast to drive on the road! I've spent too much on 98 octane in the past week, but well worth it. My mate (Jonny) and I have been taking turns behind the wheel and the other in the passanger seat with the hand controller, and last night have pretty well sorted out the tuning side, the motor is purring along. I've set the rev limiter to 7000, and it pulls well all the way to it. To accelerate and be ahead at the "traffic light drag" only need 3500 rpm change points, and will get up the big steep hills near where I live in 5th easily. Back a gear (or two) and it takes off well. The LSD is tight, and I'm happy with the overall gearing and tightness of the car too. Will play around with the adjustable shocks in a while, but they are doing great on the curvey back roads. It ran too hot with a thermostat, but tends to run too cold (50 - 65C) without it. A few little issues like that, but all in all good. Hopefully get a few pics soon. A happy driver, rob. Edited November 5, 200718 yr by robj Report
November 5, 200718 yr comment_207130 That's Rob there playiing with the very old Wolf 3D. ....and a mad grin! congrats. Report
November 5, 200718 yr comment_207137 thats so so awesome... congrats on finally getting it all together... :) Report
November 5, 200718 yr comment_207196 wow truly amazing build, much respect for the engineering :) :dance: Report
November 5, 200718 yr Author comment_207272 Thanks for the comments! Took it for another spin last night, ahh the joys. Report
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now