4a

[greenmac80]

Tried a search and found nothing!

i want to know what a rwd version of a 4age gearbox is called?

is it t50?

[Roo]

Tried a search and found nothing!

i want to know what a rwd version of a 4age gearbox is called?

is it t50?

yep, you will only find a jdm 86 have the t50 behind a 4age from factory. t50 also came in the aus delivered 86 and 71 behind a 4ac

[fozz]

also from a t18

 

i would recomend u use the t18 one as the slave is opposite the exhaust

 

differences

 

ae86, ae71 t50 = 20 spline

 

t18 = 22 spline

 

ull need a t18 front half shaft to use the t18 box

[Jono]

i know at least some ae71s and ae86s have the 22 spline.

Edited April 6, 2008 by Jono

[Hiro Protagonist]

Early T-powered Celicas had the T50 too (ie TA22, TA23), but they had the 20-spline version. A lot of people get them confused and end up with the wrong box if they're not careful and do their research

[greenmac80]

Ok i am getting a silver top and city dismantlers say they have a rear wheel drive box to suit!

so iwas wondering what it was called and if it would actually suit cos they seem like dicks...

their price for a silver top was 1890

where i got quoted 1100 from another joint but they don't have any gearboxes.

so iwas gonna get the motor from joint1 and gearbox from city dismanlers.

 

Well for a KE55 corolla tailshaft what spline do i need?

cos i'm just gettin mine shortened!

Edited April 6, 2008 by blackrolla80

[fozz]

Ok i am getting a silver top and city dismantlers say they have a rear wheel drive box to suit!

so iwas wondering what it was called and if it would actually suit cos they seem like dicks...

their price for a silver top was 1890

where i got quoted 1100 from another joint but they don't have any gearboxes.

so iwas gonna get the motor from joint1 and gearbox from city dismanlers.

 

Well for a KE55 corolla tailshaft what spline do i need?

cos i'm just gettin mine shortened!

 

well u shouldnt pay more than $300 for an ae86 ae71 gearbox

 

and no more than $200 for a t18 box

 

anymore is a rip off

[greenmac80]

well u shouldnt pay more than $300 for an ae86 ae71 gearbox

 

and no more than $200 for a t18 box

 

anymore is a rip off

 

fully reconditioned is 440..

also anyone know who might make rwd exhaust manifolds for the silvertop?

[Trev]

fully reconditioned is 440..

also anyone know who might make rwd exhaust manifolds for the silvertop?

 

If you can get a fully reconditioned T50 for $440 then grab it, A rebuild cost on average 1400-1600 bucks.

[LittleRedSpirit]

Ok i am getting a silver top and city dismantlers say they have a rear wheel drive box to suit!

so iwas wondering what it was called and if it would actually suit cos they seem like dicks...

their price for a silver top was 1890

where i got quoted 1100 from another joint but they don't have any gearboxes.

so iwas gonna get the motor from joint1 and gearbox from city dismanlers.

 

Well for a KE55 corolla tailshaft what spline do i need?

cos i'm just gettin mine shortened!

 

 

$1890 for a silvertop, I just bought one with most accesories for 800. Shop around mate. They had 4 others 4 weeks ago when I got mine.

[fusion]

Only problem is hes in SA Red :). Now in my KE30 I used a TA22 gearbox and the tailshaft from a KE30 went straight on. Only problem is I needed to shorten the tailshaft by about 20mm just to make sure there was enough shaft play for travel. This was with a T18 bellhousing to a 3TC, but in relation to the spline it may help :dance:

 

However like Red said. Shop around. You may want to try AJPS on AE86dc for a 4AGE. They know there stuff and usually don't dick people around (although people may say otherwise :hmm: ).

 

Cheers Fusion

[greenmac80]

Only problem is hes in SA Red :). Now in my KE30 I used a TA22 gearbox and the tailshaft from a KE30 went straight on. Only problem is I needed to shorten the tailshaft by about 20mm just to make sure there was enough shaft play for travel. This was with a T18 bellhousing to a 3TC, but in relation to the spline it may help :dance:

 

However like Red said. Shop around. You may want to try AJPS on AE86dc for a 4AGE. They know there stuff and usually don't dick people around (although people may say otherwise :hmm: ).

 

Cheers Fusion

 

 

well toyowreck quoted me 1100 including computer and wiring loom. so i'm probably gonna pick that up this week.

then mec tec at seaford quoted around 500 for them to put it in for me inc shortening tailshaft and custom engine and gearbox mounts.

not sure if i'll need gear box crossmember made up but yeah!

city dismantlers don have any silver tops atm

[Jono]

what car is it going in?

Edited April 6, 2008 by Jono

[fusion]

You will need a custom gearbox crossmember. And if its only $500 thats not bad at all, if its done all properly. Pretty reasonable I would reckon. Does that include a service and tune up?

 

To me it sounds like its going in a KE55?

 

If your diff breaks later on, you may need to look into an ra or ta series diff with welded leaf mounts and another tailshaft.

Edited April 6, 2008 by fusion

[greenmac80]

You will need a custom gearbox crossmember. And if its only $500 thats not bad at all, if its done all properly. Pretty reasonable I would reckon. Does that include a service and tune up?

 

To me it sounds like its going in a KE55?

 

If your diff breaks later on, you may need to look into an ra or ta series diff with welded leaf mounts and another tailshaft.

 

 

well that quote is just to make everything fit.

i'll be wiring the ecu and getting it running..

yes its going in my green beastie. as for diff when it breaks i'm gonna use a t18 diff and weld on leaf spring brackets.

but if i treat the diff well it should last a while. eg no stand stills!