KENut

A rough calc tells me that 4 psi at 11:1 is the equivalent of 26psi at 9.5:1 CR. (Note: Veeeerry rough figure) What engine? I hope its well built/ & tuned

Gee I'm not that rich seabiscuit haha They are actually superlites

On KE70s wheels sit further in at the rear, so -4 all round is ok. Fronts are easier to roll/pull. I have 15x8-4 all round, pokes a little

Hi guys, Wheels. I've got 5 stockers, with all trim rings and caps - $10 Nissan mags 15inch - overrated - $30 Any interest? Cheers :fuzz:

AHAHAHAHAHHA :dance: You caught me while drinking hot tea you bastard Trev

Helmet Fire extinguisher TRACK TIME

US. But you can get all ttt items through spirited drive (syd based) on ae86dc

:) So true. Small intercooler = gooderer. Responsive

Hello again, ^ replied :) Also, I have shortened XT130 corona steering knuckles for sale. Shorter than AE86 ps arms. Will suit 'rona, 86, etc. NOT KE70 or other corollas. Cheers

Black Mountain is sweeeet. Expecially downhill on a pushy heheh. Also the road up to stromlo observatory

Hey fellas, sick of this 4age sitting here. I have $220 on it atm. I have spent $350 on parts for it. RWD stuff alone is almost worth the 220 Come get it :jamie: Thats pretty good... put a picture up?

Elongate the strut top holes with a file. :yes:

^ The secondaries are vacuum operated. Give it a good rev while looking? :)

Hey TRD ke70, keiichi on AE86dc found a supplier of 2 part Handi foam. Although its probably a bit late now :laff: rigid closed cell type http://www.erapol.com.au/english/index.html Era Polymers Head Office (Sydney) 25 - 27 Green St Banksmeadow NSW 2019 AUSTRALIA Tel: +61 2 9666 3788 Fax: +61 2 9666 4805 Postal Address: Locked Bag 7005 Botany NSW 1455 AUSTRALIA General Enquiries: [email protected] Customer Service Domestic: Dave Weir ([email protected]) Customer Service International: Louise Connor ([email protected]) Era Polymers Melbourne Tel / Fax: +61 3 9764 4452 Era Polymers Brisbane 3/3 University Drive Meadowbrook QLD 4131 AUSTRALIA Tel: +61 7 3299 7135 Fax: +61 7 3200 3663 Era Polymers Singapore Tel: +65 9751 0026 Era Polymers Adelaide Tel: +61 (0)403 451 223

Are you sure its 298? Could it be a 3? Because then it might be a wade 293 Stolen from altezzaclub http://www.rollaclub.com/board/index.php?a...st&id=56223 Edit: just checked the hires pic, defs 298. :) Back to searching

Well the 298 suggest its BIG, Unress thats the companys cam code hmmm.

Yes they are 5 x 7 inches

Regulator? Thats where I'd start, I'm no sparky though :)

Neat car :) Looks like it has a little rust behind the drivers rear mud flap. Other side is missing a mud flap, which says to me it may have had rust repairs there. Check for bog And check boot wheel well, and the inner arch from inside the boot for rust Looks like a few lil oil leaks Has a tacho dash, which is a little odd if it is a CS auto (but as Shady said, its got csx trim) Check the inside leading edge of the bonnet for rust too & around the fuel flap Front bumper is bent in a little I'd prolly buy it, you should be able to knock that price down a fair bit.

See, thinking ahead. Much easier that way (engine out), especially with a bit extra thread to grip on

There might not be room for the 2 nut trick, but easier than vice grips on stubborn studs Only use a lil bit of gasket goo

Spotted a yellow KE70 wagon and a red sedan with chrome bars in the bruce area tonight

can't say I know anything bout adm and jdm being the same/different sorry mate. I'd guess they're the same don't worry, you're still working faster than me! :wink:

Hey guys, So I need to get some new chassis rails bent into shape (not for the corolla haha) Does anyone know where I can get steel mandrel bent in 'Berra? Like 2 x 4" rhs Thanks

If autopro or one of those places can't sort you out, there is a bearing shop opposite specialty fasteners in fyshwick (I think) Yes, there should be an inner and outer Some nice gear in your panno! looks like fun :lol: