AExx Corolla Discussion
1398 topics in this forum
-
Hello guys, I am trying to build love to a good condition AE86 with 4AC and keep it original for the moment. There is not logical issue however and being out of ideas I am reaching out for help. The cylinder one refuses to work, no matter what. There is spark, a good one. Distributor revised. There is fuel. Tried with different carb from working 4ac. There is good compression on all 4 (12). Valves have been adjusted 3 times and are in spec. The car is running smooth on the other 4 otherwise, starts first try. Runs rich, I assume due to the not burned fuel in cylinder 1. I am really out of ideas what to do next. Anyone had a similar…
-
- 5 replies
- 207 views
- 1 follower
-
-
Well, the Girls KE70 has had the 4AGE for 5 or 6 years now, and more recently a Haltech running it. Behind that is the lightest flywheel I've ever seen, and a pair of Wade 267deg cams, extractors and a 2" exhaust, all on the stock inlet system... It has always been a dog low down, even with a stock ECU it couldn't hold an idle, and the last mods were Banjo making me a Hall Effect sensor setup for the distributor and a set of COPs. Then it died earlier this year and I found enough carbon under the valves to drop the compression at cranking speed, and the TVIS plates heavily carboned up. Having made some movies under the inlet system with an iphone I realise…
-
- 1 reply
- 141 views
-
-
Adjustable cam gears second hand good condition around Brisbane area
-
- 1 reply
- 163 views
-
-
I fitted some dash parts into my ae92 hatch from a seca which included the digital clock and I was suprised Toyota hadn't included the wiring for the clock in the loom 'cause normally most things are provided for in the loom even if they aren't going to be installed. I swapped the dash top so I had a good oppurtunity to check the loom... Does anyone have a wiring diagram showing the clock or an easy way to wire it up?
-
-
- 15 replies
- 65.2k views
-
-
Howdy Corolla enthusiasts. I'm in need of a new diff for my KE70, i've heard the T series diffs are the way to go. I am planning on putting a 4AGZE in it and was wondering if that is still the case and if so where should I look. I've seen some people have luck finding T series diffs out of RA60 Celicas. There are a couple of unnames 3rd Gen Celicas in the yards around me. How would I know if they have a T series (sorry, I'm a bit of a newbie). Thanks in advance!
-
- 15 replies
- 3.4k views
-
-
Hey folks, I have a '99 Corolla with the stock 1.8 7A-FE motor. It intermittently surges when idling (i.e. - pulling up at lights, fluctuates between ~ 500-1200 rpm), but doesn't do it all the time. Sometimes a quick press of the accelerator will stop it and it'll return to an idle of around 800 rpm or so, sometimes it doesn't. For the first few minutes after cold starting, the car will jerk a bit at low speed, but goes away within a few minutes of running. Local mechanic has sprayed the throttle body, and it's had a recent full service (air and fuel filters, plugs and leads etc.), but it hasn't made much difference, aside from alleviating the sticky accel…
-
- 61 replies
- 16.9k views
- 1 follower
-
-
Can also swap for complete 2TGU 1600 that suits rebuild head valves crank block pistons and rods in good condition. Or will buy 4 age parts outright please message Shane Genn on Facebook Location Brisbane Queensland
-
- 0 replies
- 227 views
-
-
I am chasing a 3.7 or 3.5 Jap diff centre to fit a KE30 Corolla in Australia if anyone knows of one it would be appreciated. Thanks in advance Gary
-
- 0 replies
- 180 views
-
-
Hello. We have a 1995 Corolla Base model/1.6L, which we don't drive too often (keep it for when our other car is in the shop). Anyway I have 2 questions/issues I could use help with: #1) Last time we drove the car we noticed that the speedometer wouldn't work until we got to about 50+ MPH - then the speedo would jump up to 50 or so MPH. As long as we stayed above about 50 MPH the speedo would register a speed. Once we dropped below 50+ MPH - the speedo would drop to zero. Was told it's probably the 3 capacitors on the back of the speedometer. So I changed them out but it still doesn't work?? Could it be the speed sensor? Or does the fact that it starts working whe…
-
- 0 replies
- 291 views
-
-
Hey everyone, Thank god forums like these are still around. This is my first post on this particular forum, but I have been a member of older ones for over a decade. Have also been a long time Corolla owner (have had a AE82, still have the 92, and had a Sportivo). Anyway enough of the history lesson. My modified 92 has been sitting in my garage for 7 years. I have turned the motor over at various times and it’s always ran perfectly. In the last year I’ve had trouble starting the car and I really want to bring it back to life. The motor turns over, spark plugs spark, but the motor doesn’t start. My best guess is that it’s the fuel pump, as I can’t hear it turn on…
-
-
- 43 replies
- 22.6k views
- 1 follower
-
-
Hey, I have recently swapped a 7afe in my ae95 and having some issues with idle from start up. The 7afe came out of an auto ae115 so have had the two wiring looms spliced together and running the 7afe ecu. The car starts but has an idle of 2k then creeps up to 3k and sticks there for a while once the throttle has been opened. I have checked for leaks and can't find any, cleaned the throttle body, cleaned the iac valve and checked timing. Any advice beyond this? Cheers
-
-
- 3 replies
- 565 views
-
-
What is the proper valve lash and adjustment on a 83 toyota corolla AE71 4AC 1.6 engine ?
-
- 1 reply
- 526 views
-
-
Hey rolla guru's So I got an ae82 recently 86' with a 4ac motor 70k km on the odo and I can't get the thing to idle for more than a minute once it starts up. It hadn't been started for over 2 years I'm thinking it's probably the idle jet and I'm gonna pull the carb apart this weekend to give it a bash with carb cleaner. If that doesn't work tho I'm wondering if I can just whack a 4af carbie on to replace it as they are dead cheap on ebay. Anybody had any experience with this?
-
- 7 replies
- 1.4k views
-
-
I'll try to be brief: Q#1) I'm a disabled senior with a balance problem (I can't stand long and I fall a lot). Anyway, we have a 1995 Corolla (base model, 1.6L, automatic transmission, 172,000 miles). It was my birthday, It was 105+ outside, and I had a coupon for a full synthetic oil change for $19.95, and the tire and lube place had just changed my wife's car oil without any problems. So I had them change the oil, and because it was sooo hot outside, I didn't check the oil level on the engine oil dipstick before leaving. The car drove home great - no issues (14 miles). Got home & parked the car, where it sat for 2 days. Needed the car and it wouldn't start…
-
- 9 replies
- 629 views
- 1 follower
-
-
Hi All, I'm in the process of modifying the intake on my 1991 AE92 4AF (carb) corolla. I started to pull the stock system out and came across some mechanism attached to the air filter housing. It appear to be connected to the cooling system (maybe for cold start assistance etc.) Pic attached. The question is, can I just remove this and assuming it's part of the cooling line just bridge it out completely to maintain coolant flow. I am working towards a 32/36 weber setup. Thanks
-
- 21 replies
- 107.4k views
-
-
Hello everyone, I recently purchased a complete 20V Blacktop that came with an auto ECU and harness. I'm going to install a 6 speed manual gearbox along with the engine on a AE92. I've done some research and apparently there's 2 wires that need to be joined to trick the auto ECU into thinking the car is neutral but I couldn't find any in depth explanation. Can anyone help with this subject? Thank you!
-
-
- 4 replies
- 2k views
-
-
Hi guys, I've recently bought a 1988 corolla with a 4ac and it's acting up quite a bit. When it's completely cold it will start up with no problem, but when it's hot it is very temperamental, sometimes it will start sometimes it won't. It's getting very annoying as it's leaving me stranded a lot and I have to get picked up. Any ideas why this would be happening any information would be greatly appreciated. Cheers
-
- 11 replies
- 1.3k views
-
-
Hi guys, as the title implies, on my 4ac, it starts up fine when cold but idles high, around 1500rpm, and adjusting the idle speed screw doesn't change anything. Also intermittently the idle drops to 500-600rpm and will stall if it's not in neutral (automatic) (maybe running too lean?). I took off the air cleaner, sprayed some carby cleaner, and checked for vacuum leaks, but it didn't help, the fuel filter is clean and I haven't had any problems with the fuel pump before. This problem hasn't happened before (in the past 4 months), it only started a couple weeks back after the engine shut off and wouldn't start till 30 mins later (I suspect it was a vapor lock) but i …
-
- 6 replies
- 1.3k views
- 1 follower
-
-
hey guys, I'm doing the head gasket on my ae82 4ac powered corolla and I would just like to confirm which marks to line up to get the timing correct when doing the timing belt thanks in advance Chester
-
- 7 replies
- 70.6k views
-
-
Hi Team, My front and rear bar have some decent wear from a little Bingle, would anyone have any videos or tips on how to respray the black bars?
-
- 1 reply
- 402 views
-
-
Hello corolla people! I have recently acquired another corolla, an ae71 auto sedan. Currently has a borgie in it. I have got some very nice shockworks suspension on the way and chasing the last few manual parts to swap into the vehicle. I want to eventually fit a lsd rear in the vehicle. Currently getting parts, (and money), for a efi smallport 4age swap. I know the borgs don't support lsds, so a new diff is needed! I have done a fair amount of research and commonly people suggest slapping in a japan spec T-series from a Corolla. However, those are few and far between and are costly to import and or purchase locally. T-18 diffs are also out of the questi…
-
- 2 replies
- 1k views
-
-
Hi All, I am trying to get my car over the line for a compliance certificate and l have been advise l to need to relocate the Fuel pump and serge tank + accessories under the car to pass. Has anyone done this and would you have any ideas on where to locate these items as space is a nightmare. Thanks In advance guys!.
-
-
- 3 replies
- 936 views
-
-
I am planning to implement Fully Overhaul on Engine Toyota 4AFE 16V on the Corolla AE111 (Malaysia) 1997 car model. For that purpose, I would like to install 16 new valves to Stainless Steel Valve for 4AFE head engine. Anyone can help me, can I find that valve?
-
- 0 replies
- 355 views
-
-
Hey guys I'm sure this has already been touched on somewhere, but I had a quick search and couldn't find exactly what I'm after. I'm trying to look into suspension upgrades for my AE82 and I'm not having any luck at all lol. What I'm after is everything and anything, I'll be building a track car soon as well as wanting to upgrade my street car, too! I'm aware BC coilovers are available, anything else I have absolutely no clue. I'm interested in everything and anything! Even if I won't bother with certain bits I'd still like to know what is out there! Any information would be much appreciated! Websites, builds, people to talk to. I want to…
-
- 3 replies
- 3k views
-
-
Hi there Rollaclub I have a 1990 Corolla Seca (without aircon) and looking to transplant an air conditioner already removed from another Corolla, into it. Does anyone have a digital copy of the Air Conditioner Installation Manual (photo attached) that could share? Thanks in advance S
-
- 1 reply
- 755 views
-
-
https://www.news.com.au/technology/mans-1993-toyota-corolla-car-hits-two-million-kilometre-milestone/news-story/2f09951cdcac40d225a088a907366ae6 Saw this story in the past week, on a news feed, & was instantly skeptical. However, when you do the maths, it is quite possible, if my maths are right ? The Corolla was a 1993 model. It tipped the 2000,000 klm mark recently, in 2022. That's 29 years of service. If you divide 2 million klms by 29 years, you get approximately, 69Klms per year. Assuming the car was only driven on works days, of which there are 261 per year, the car would have travelled 265 klms per day. Assuming this Coroll…
-
- 0 replies
- 741 views
- 1 follower
-
-
Hello, I have a 1995 Corolla (1.6L, 150,000 miles)) and it failed the CA emission smog test (Failed the Nitrous Oxide/NO test at 15 MPH/Passed the NO test at 25 MPH). Smog tech said I should have run the car for at least a 1/2 hour before bringing it in to be smogged so everything was HOT (oxygen sensors, catalytic converter) because the car just barely failed. Put in some better gas & drove it an hour at 60 mph and drove back to the test place (kept the engine running until the guy took the car into to be tested. Now the guy said it failed again, but his time because the EGR valve failed?? He said the diaphragm in the EGR isn't working. Sounds plausible except that t…
-
- 3 replies
- 877 views
-
-
Hello I just purchased a AE82 1986 model and I'm after a dashboard does anybody know where I might locate one
-
- 0 replies
- 959 views
-
-
Hey guys, my 7afe AE112 has a very high idle (1600-1800) and i don't know why. I have already cleaned the IAC and not seen a difference. Is there anything else i should be looking at to get my idle down? Thanks
-
- 6 replies
- 2.8k views
- 1 follower
-
-
Hey guys just got my first car and is it wrong to say I'm absolutely in love with it? Its a 94 corolla csi limited bare stock gets me places but its not as nice looking as it could and should be. i was wondering what upgrades would be worth and COULD be done to the ae94 without going full engine swap crazy. I'm a big noob to the whole car scene so i wouldn't even know where to look or what to look for quality wise.
-
- 1 reply
- 787 views
-
-
Sup everyone, Does anyone have a source for gear bushings for a 98' ae112, I'm trying to get the play out of my knob? Thanks yall
-
- 4 replies
- 1.2k views
- 1 follower
-
-
Okay, so I'm completely and utterly uneducated about this, so I apologise for such a daft question if so. Basically, my Rolla is running on stock wheels and I frankly hate them. But my cousin owns a Mirage with aftermarket wheels and I wasn't sure if or if not these would be able to fit an AE92 Corolla? I'm not sure about like the spacing and all that jazz of the bolts... So can someone give me the briefs? I know that manufactuers like Holden/Ford make their spacing different to prevent fitting the same wheels. But is that the way for every manufactuer? It'd be nice to know. Like I said, sorry for being completely foreign to all this, I just thought it'd be a…
-
-
- 19 replies
- 192.1k views
-
-
As title states I'm trying to find out which 4age this is from so I can order a clutch to go with the w57. It has about 230mm of diameter if that helps.
-
- 2 replies
- 1.3k views
-
-
Toyota Corolla AE111 Lip Demold and Installation http:// https://www.youtube.com/watch?v=xBygIxyqEu0
-
- 0 replies
- 787 views
-
-
Hey guys, i bought some work equip reps for my 82 and on inspection without the tire fitted it looks like they'll rub without spacers. Can someone recommend any hub centric spacers? I know i could get some on ebay but id rather ask here first before turning to something cheap from ebay. Also thinking about getting coilovers and am set on BC's. Thoughts?? For the meantime i was thinking of just getting some camber plates for the stock struts.. Has anyone done this and is it "worth it"?
-
- 1 reply
- 1.3k views
-
-
Hi all, i need a part number for a set of igniton leads and am after advice on which brand to use.
-
- 0 replies
- 660 views
-
-
Hi all, is there any difference in the water outlet pipe for the back of the head that runs along the side of the block between the ae82/ae92/ae86 etc 16v 4age's?
-
- 2 replies
- 1.2k views
-
-
Hey all! Having issues getting my smallport started in my AE82 after conversion. •Using AE92 Smallport ECU / Engine Loom •Ignition side/Body harness connector for ECU wired up by auto electrician I got it home from the auto leccy, my lights now worked and all the rest of the electrical that should be powered from the ignition- INCLUDING the car wanting to crank over now. Yay! They've plumbed the body harness' connector into the engine loom and wired up the starter relay etc different. I asked if what they've done is different to the factory set up and they said no. My close mate thinks they could have mucked up the starter relay?? …
-
- 18 replies
- 3.5k views
-
-
Toyota Corolla AE101 FX LIP Part 1 (Molding) https://www.youtube.com/watch?v=UpQ2I5bFR-o
-
- 0 replies
- 640 views
-
-
Was looking at lowering the corolla, i have the 2000 hatch and was trying to look for some coilovers and can’t find any for it. I have found multiple for the ae111 or 99 model and was wondering are they compatible or is there a way to make them fit? thanks in advance.
-
- 2 replies
- 2.2k views
- 1 follower
-