AExx Corolla Discussion
1398 topics in this forum
-
Hi all, new here. :wink: I have a 1992 Toyota Corolla CSi Twincam AE94 sedan. It has a 4A-FE engine and a 4 speed auto (3 speed, plus overdrive switch on lever). It doesn't have a tacho on the dashboard, however it has the fuel guage and temperature guage in the right hand "big circle" where the tacho exists on other versions. I am wondering, is it possible to simply replace the cluster with a tacho, and do I have to modify any wiring to make it work? I have recently been offered a aftermarket tacho, so I don't know if that is better instead or what. Thanks in advance. :)
-
- 7 replies
- 4k views
-
-
hey guys, i have a ke70 with a blacktop 20v and a t50 behind it the speedo does not work i have swapped the speedo cable and the speedo itself. and it still does not register speed, I'm guessing the shaft the bolts into the side of the gearbox is replacable? ie "the send unit"? which is mechanically drivin? guessing toyota has these?
-
- 2 replies
- 1.4k views
-
-
Hi all, i just had a quick search, and was wondering if anyone has converted the ke70 cable pedal box to a hydraulic set up? I have been looking into it with a mechanic mate of mine and he thinks it can very easily be done, as i refuse to pay $300 for hydro box :no2:. I don't see why it wouldn't either, as it would just be locating a tab of plate metal in the correct position and welding it onto the side of the pedal arm. Let me know if anyone has done it and if it worked or not! cheers
-
- 9 replies
- 3.6k views
-
-
hey guys I'm building an ae71 with a 4age for drift wondering if a te71 welded up diff would be strongh enough to cope? if not what would be?
-
- 4 replies
- 4.7k views
-
-
Hi Guys, Just reading the topic below and the problems Skippy1331 is having, and I'm having a similar problem with my AE82. I have done all the things recommended in his thread (fuel filter, tank, carby rebuild, vacuum lines etc etc) but still have the same issues. Huge flat spots and surging. I get a flat spot turning left and sometimes it snuffs out, and big flat spot every time the secondaries open when I put the foot down. I have had the carby reconditioned 3 times in 3 years (on recommendation from mechanics) and I've had no luck, the problems persist. On the subject of tuning the carb. The last time I had the carby reconditioned I dropped the car off at my…
-
- 20 replies
- 27.4k views
-
-
hi i recently posted about my carby having problems that was my fault as i let the fuel get way too low and crap from tank,some how got throught the filter and intot the idle jet, thus it would just stall. now that it is fixed :hmm: ($600 later) i find that when i put the foot down it jumps as in it wants to keep speeding up but skipps so to speak. it only happends below about 2500 rpm. i don't know if it is a clutch slipping problem, or something along those lines. would be great if anyone has had the same problem.... :blinks:
-
- 8 replies
- 5.4k views
-
-
hey just wondering if anyone know of any other radiators that will fit a toyota tercel sr5 4wd??? ive hear AE71 might fit??
-
- 2 replies
- 2.3k views
-
-
Has anyone converted the dizy on a BT/ST 20V to the front of the motor before? like this one...in the attachment if its easy, would it be a better option than running CAS and coil packs, for those on a budget? found this on http://speedhunters.com/archive/2010/11/03/car-spotlight-gt-gt-20v-ke70-corolla.aspx
-
- 1 reply
- 9k views
-
-
Hi all, I am looking at buying a 4agze off a mate, but I'm not sure how or if i can I.D the motor as far as knowing what car it came from e.g mr2 ae92 ae101? I know the later models had MAP sensor and earlier had AFM, it doesnt have the airbox, loom or ECU with it. If its MAP sensor where is it located on the manifold? I also know that it runs CAS not dizzy, so its either been converted or its a "later" version... thanks for the help
-
- 3 replies
- 3.3k views
- 1 follower
-
-
-
Hey all, Recently changed my clock cluster in my ae82 to a tacho one. It works perfect, until the cars temperature reaches almost half way and then it starts jumping around and giving the wrong reading. Ive pulled it out several times to check the wiring and plugs but still nothing. Anyone got any idea's? Cheers Corey
-
- 10 replies
- 6.4k views
-
-
Does anyone know if the rt132 corona LCA's are the same as the xt130's corona? Thanks for the help
-
- 0 replies
- 2.5k views
-
-
hey guys I'm thinking put exhaust on my ae71 currently running a 4ac but the 4age is coming one day. I was thinking 2 1/4 and one muffler just wondering what system other people are running?? or recommend
-
- 7 replies
- 5.7k views
-
-
Hi all, i have been looking at doing 4 wheel disc brake conversion on my ae71. I was thinking of using rt132 corona front end basically unbolting the LCA (lower controll arm) and the top of the strut form the tower and slotting it in the ae71 for the fronts, and using a rt142 corona diff with disc brake for the rear. I know i have to get the mounts on the diff modded, is there anything i have to do to the front end? such as strut camber tops and master cylinder? Also the rt142 diff is slightly wider 1420cm i think, but i don't think this will matter as I'm using the corona 14's, so using the rt132 LCA would that make the track up front wider? If it does, it wouldn'…
-
- 0 replies
- 12.5k views
-
-
I have a ae92 seca and was wondering if anyone has.used the running gear from the ae95 wagon to convert a seca to awd. If so could I get some specs please.
-
- 8 replies
- 16k views
-
-
I think my AE95 is running hot (4AFE with a manual box) Its showing halfway on the temp gauge after 40 mins of use but when i feel the bottom hose it feels warm only. I have Replaced the thermostat with a toyota one which i placed into 85 deg water it opened and seemed fine. Removed the water pump, all good. (flushed the metal pipe that runs behind the engine) Removed the raditator fed water through it backwards.( a bit of orange rust) Removed the head replaced the head gasket, cleaned all the jackets out while there. It is not using water it, runs good. The cooling fans only come on for a brief moment. Still I don't think its right, that bottom hose seems t…
-
- 22 replies
- 18.1k views
- 1 follower
-
-
hey guys ok so i had a little accident the other day end result was that the drivers door got badly damaged and wont even close so I'm in need of a new drivers door asap please!! its a AE82 Sedan i badly desperately need one i went to wreckers and they had no sedans so got a seca driver door...it dosent fit i have next to no money but please help a desperate corolla person in need Located in Brisbane email: [email protected]
-
- 0 replies
- 1.4k views
-
-
Hi all just wondering about these parts from white line, it may be a stupid question but are all of these parts interchangable into the AE71 even though they're listed for AE86? I know some parts are, just wanted confirmation! Toyota Corolla AE86 5/83-5/87 Sprinter Levin F Brace-strut tower alloy adj. KSB519 1 S R Quick Release clamp kit available for this brace. KSB790 allows for rapid removal of alloy centre brace. F Swaybar 24mm-h/duty Blade adjustable. BTF35Z 1 H S R Replacement type. 3 point adjustable. F Swaybar 24mm-heavy duty. BTF35 1 Replacement type. Non adjustable. R Panhard rod kit-adjustable. KPR010 1 S R Off-car adjus…
-
- 6 replies
- 11.4k views
-
-
I have a Sprinter Carib AE95 in Minnesota, USA. They are super rare and used parts are pretty much non-existent. What is a good source for used parts online? Specifically I need a differential lock diaphragm. Any suggestions?
-
- 1 reply
- 3.5k views
-
-
does anyone know of a company that does off shelf 1st 2nd 3rd straight cut dog gears? i can only find someone who will do custom ones to suit at over $8000 instaled.
-
- 9 replies
- 25.9k views
-
-
So kids, I have this lovely AE82 Seca, 4 speed auto and a well used, compression losing, oil chewing, 4AC. Now I was wondering about getting more fuel for the Ks then the Km/h... having all that power compared to the weak 2A from the old rolla, I got thinking, what if I leaned out the carby to the point the exhaust is coated white (and burning seals and rings and other things) for a little less power and more range... on the other hand in the European and japan market, there is such thing as a CE80, or a CE90/96/97 that uses the C1 toyota Diesel motor (mmm, diesel AWD corolla ...ahem), that got me thinking, what if I find a townace or a liteace that had one and droppe…
-
- 33 replies
- 45.2k views
- 1 follower
-
-
can you put a 4age big port head on to a 4afe block looking at the engine specs they both seem the same exept for the compresion. can a 4age crank be used in one
-
- 6 replies
- 21.6k views
- 1 follower
-
-
Hi all, ive had a quick scan through the site and was wondering what rotor/caliper upgrades can be done, Ive got a 93 model seca (ae94) with the 4afe,automatic. The brakes are ok, but with heavy traffic they tend to fade. Have done the usual bleeding new fluid, changing pads, there isnt any leaks anywhere. Thanks in advance for all your help. Paul
-
- 6 replies
- 4k views
-
-
as the title suggests I'm looking into power steering for my ae71 rolla could i possibly use a power steering rack from an ae86 or would it just be a waste of time and money aswel advice is appreciated thanks aj
-
- 3 replies
- 2.6k views
-
-
Gday, I'm currently building a 4agte for my ae82 Twincam. I brought what was a rebuilt 4agze block already fitted with Aries 8.0 forged pistons, spool rods, and its a seven rib with oil squirters. All good, then whilst I was checking the mains with plastiguage I found that the crank has been ground undersize and therefore has thicker "standard" type shells, I figure I really need to run the acl grooved "race" type as I will be heading north of 20 psi but these are not available in the shell thicknesses this ground crank requires. My question is what is the best crank to source, and are GZE and GE late, large journal cranks the same? I've read conflicting info in reg…
-
- 14 replies
- 24.6k views
- 1 follower
-
-
hey everyone I'm doing the head gasket on my 4agte corolla this week and I would just like to confirm which marks the cam gears line up with when doing the timing belt? any help would be greatly appreciated. :) thanks
-
- 5 replies
- 52.6k views
-
-
Hi got a bit of a problem with my 4age conversion and need some help i have got a blue top 4age with a map sensor & tvis and am unsure which ecu i need the engine is origanaly a rwd so does that make it jdm??? anyway the ecu plugs are yellow any help gratefully appreciated Marcus
-
- 1 reply
- 2.4k views
- 1 follower
-
-
Was driving my 88 AE92 4afc today and was going up a hill and when i was going to gear down for a light i noticed that the car was jerking and surging on trailing throttle. i put the clutch in after realizing this and noticed that the car was idleing at 2000rpm. I pulled off the road to check under the hood and looked around and saw that a vac hose coming off what i think is the high altatude filter box thing. After puting the vac hose back on it made no difference. I decided to get home as soon as possible and drove for about half an hour then i noticed the car was driving perfectly again. I was on a mountain a fair ways above sealevel. I drove to a friends house and che…
-
- 2 replies
- 3.4k views
-
-
Hello, I have a set of extractors that I took off a seca ae92 with a carby motor.I want to fit them to a EFI motor.Are they the same,will they fit? I have been told that the heads are different between the carby and efi motors.Is that only the case with the inlet side,not the outlet side.As far as I know,it is a 1.6 dohc 4afe. Can supply pics but I figured they are not needed. Any help is appreciated. It would solve my problem if someone out there swapped me a set that would fit(just a hint LOL). PS; I know the bit that bolts together on exhaust system is different.That can be welded together,does not …
-
- 2 replies
- 2.7k views
-
-
alright so i wanna weld the diff in my AE71, but ive never owned a corolla before. so would it be better to wait for next winter to come around, or just go for it? and are all the axels and stuff strong enough to drive it around day to day, or should i start collecting a few spare diffs, axels etc?
-
-
- 14 replies
- 6k views
-
-
With summer coming and a few threads popping up about cars running hot I thought I would post up how I always have/had flushed my cooling systems, next time I do a flush I will get a step by step photo guide. 1. Turn cabin temp to hot. 2. Undo drain cock. 3. Pull the heater hose off of the top of the thermostat housing. 4. Insert hose into heater hose and turn on. 5. Let the water run out of the heater pipe until clear. 6. Once the water is running clean use your finger to block the heater pipe on the thermostat housing so the water backflows through the engine. 7. Once the water from the drain cock is running clear turn the tap on a steady rate so that the wate…
-
- 2 replies
- 3.5k views
-
-
i have a 1985 corolla gt-s coupe and i have a couple questions. theres no power going to the fuel pump but i checked all the fuses replaced the relay replaced the pump and still nothing. so i hooked the pump up straight to power and it starts and idles for a couple seconds then dies. and if i try to rev it up when its idleing it will just die instantly. i don't know much about these cars so someone help me i need this car running so i can get it out of my drive way ive searced and searched and i tihnk ive checked everythiing that should be checked but i have to be missing something
-
- 17 replies
- 19.3k views
-
-
Soo.. When I purchased the car (AE92), only the drivers door opened with the key.. The key goes in and turns inside the passenger lock, but doesn't do anything.. If i rip it off, could it be something simple to play with at home or not worth fixing? Suggestions? I'm not good with this kind of thing and decided i'd ask here, seeing as you guys have probably pulled these cars apart a lot more than I have. Cheers :)
-
- 15 replies
- 6.4k views
-
-
Right.. So how do I go about removing the outer black strip on the doors? Is it just held in place with some form of glue-substance or is there more to it? Mind you, it's for a 1989 AE92 CS Corolla, I HATE the look of the black along the side and would LOVE to keep it looking clean and crisp. Any help is appreciated, thanks guys!
-
- 14 replies
- 11.6k views
-
-
Hi, I was wondering if the Lower Control Arms and the Caster Bars on a AE86 are the same as any other Corolla eg KE 55 or 70. Thanks. Stefan
-
- 2 replies
- 2.5k views
-
-
Hello, I have new rear wheel bearings and brakes to fit to my ae90 corolla hatch.I need to know whether the rear bearings have to be pressed in or are they fitted by hand.Also how much greasing do they need when fitted. It may sound like a dumb question but I don't want to have the car in pieces and then find out I have to carry parts down to a mechanic to be fitted.The car has rear drum brakes,not disc....Thank you.
-
- 1 reply
- 11.6k views
-
-
I'm trying to identify the distributor in my 100kw motor. The serial number sticker is long gone. pics hopefully attatched. Does anyone have the part number for the 100kw motor???. The pic of the one with the rotor arm is - I believe to be out of a redtop bigport. Can I use this sucessfully in the Smallport motor Many thanks Bob
-
- 5 replies
- 13.1k views
-
-
Hey all, I recently cracked the cylinder head of my ae82 twin cam and decided to save on the labour costs by doing it myself. Bought the workshop manual, took it all apart carefully, sent off the cylinder head had it all welded and fixed up, put it all together again with the help of a mate who's a bit niftier than myself and... she turns over but won't start. I have checked the plugs and they are all sparking, the fuel is getting to the gallery and the dizzy should be in correctly but she just isn't starting. Everything "should" be back in the right. Does anyone have any idea why she isn't starting? What can I troubleshoot? Any help would be appreciated muchly. Nick
-
- 2 replies
- 2.8k views
-
-
Hello, does anyone know how to wire up factory electric windows in an ae90 corolla?? any info will help and will pay for labour if you can fix it,if local brisbane. Everything was removed from an ae90 seca and I want it put into my ae90 hatchback.Everything seems to just plug together(central locking works)except that one plug under the dash has a black wire that goes no where(and obviously it goes somewhere).I have a corolla wiring book but it tells me shit. Can anyone help or recommend a local (and honest)auto electrician. PM me or call 0413 960 696...Goodna,Brisbane...Thank you. ALSO... I need front spoiler and side s…
-
- 5 replies
- 4.4k views
-
-
Hey guys, I have an AE71, and I was curious if the front struts from an AE82 or 92 or whatever model are interchangeable? Any advise is much appreciated. this is my first rolla. yew! :D
-
- 21 replies
- 13.6k views
-