Engine Conversions
Toyota Engine conversions - Q & A
1441 topics in this forum
-
has anyone heard of a ke55 with a 20b in it before and if so was it able to be regestard? i will put a series 6 trans in it (or alike, a hilux diff and appropriate suspension so on and so on.
-
- 22 replies
- 12.1k views
- 1 follower
-
-
HI, i know this is a Rolla site, but me and my mates got more Toyotas than we can poke a stick at... Got a 4wd 1998 Hilux with 3L (aftermarket Safari Turbo) Diesel. PLENTY of torque ;) not having a great deal of luck after 3rd rebuild.... Ouch! WHat else from the Turbo Diesel 4cyl family is an easy conversion (4wd still needs to work!) Proven, is what i need to know, not throwing $ at maybes cheers
-
-
- 7 replies
- 20.7k views
-
-
Hello everyone. i am a new member of this forum. i have two cars ke30 and ke70. both of them are stock. i want to change one of my cars engine to 3s-ge/3s-gte or atleast 4a-ge blacktop. but i am not sure which car shall i choose for modification. as i am a 22 years old and my dad will allow one car to choose so i am confused. please help me to decide what car shall i choose and what engine will be better for the car. i like 3s-ge or gte because of the power but i need to know the advantages and disadvantages.
-
- 11 replies
- 5.2k views
-
-
I have a 3T-GTE and everything that goes with it(gearbox, k frame, exhaust,etc) out of a KE25 i was planning on putting it in a KE20 but can get my hands on a cheap KE10 iwas wondering if anyone would know if will it take much extra work to fit it to a KE10 as i have not had much to do with these thanks
-
- 8 replies
- 9k views
-
-
Has anyone used an ae71 radiator when doing a 4age install in a ke2x? If you have can you use or modify the ae86 4age radiator hoses they sell on eBay to plumb it up? Cheers, Ben
-
- 0 replies
- 3.6k views
-
-
hey i was just wondering if anyone could tell me how do you turn the fwd 4age into a rwd motor? and would it be possible to do this to a starlet gt turbo motor as i was thinking it would go alright in a 69 rolla and i don't think it has been done yet have they. cheers
-
- 3 replies
- 3.6k views
-
-
hey has any one done a 4age conversion on a ke11 and what did they do to fix the steering arm hitting the clutch slave cylinder, also I'm in the process of making engine mounts i have my engine in but it looks like it is leaning to far back, there is about 25mm from crossmember to sump clerance also, any one no how it should sit cheers
-
- 0 replies
- 3.1k views
-
-
gday guys iv just pulled out my gear box out of my ke55 which has a 5 speed box in it, due to grinding and thrust bearing noises although my problem is i don't want to rebuild it yet bcoz i have a 4age built ready to go in and the box doesnt bolt up?? so how do i go about this do i need a adaptor plate? bcoz from what iv heard they are meant to bolt up..its out of a ke70 5 speed. so can i use this box with my 4a or do i need a different one? help would be muchly appreciated thanks
-
-
- 16 replies
- 10.2k views
-
-
hey everyone, so iv started my conversion and i am a bit lost on some things, what do i do for a tailshaft? is there a way to change the yoke on my old one? iv got standard diff with a cable t50 box.. i think its 22 spline. and will i have to make my own g/box mount? help would be great. cheers
-
- 0 replies
- 2.8k views
-
-
hey people THE ULTIMATE SLEEPER KE20 BURNOUT MACHINE a while ago I purchased a matt black ke20 with and XE 250Xflow in the sucker. considering it cost me 300 bucks and it was running I was stoked. some specs -Engine/Running Gear XE 250 crossflow (stock) 350 holley extractors 3"exhaust borg warner 35 trans shortened XE tail shaft shortened and locked XE diff (converted 2 114.3PCD) soon to be EFI & SUPERCHARGED 16" thermo trans, engine, diff oil coolers -Interior was bare when i bought it soon to have complete black interior 5" tacho with shift light Amps, Oil Pressure, Coolant Temp, Vaccum and Fuel after market gauges. …
-
- 36 replies
- 16.7k views
-
-
for an Sr20Det conversion. you are able to use, s14 x members, lca, tie rod ends etc (basically whole front end, suspension) into ke70, would this make the conversion a lot easier therefor the sr20 would bolt straight onto mounts. and how easy would it be to convert all the suspension. eg straight bolt in slight adjustments cutting fabricating etc. thanks, Jamie.
-
- 2 replies
- 2.7k views
-
-
what are everybodys thought on this, good idea or bad? what troubles would i have, how difficult would it be to do? thanks.
-
- 19 replies
- 42.8k views
-
-
so I love my ke70, but I'm not the biggest 4k fan... do I've been toying with the idea of an 18-RG keto. why? - carbs! fuel injection just isn't sexy... - twincam - good following, proven performer - something a little different now, I know it's been done before, and I'm a bit of a rolla n00b, so I was wondering if anyone had some pointers/ rough projection of costs/ knows where I can get one/ general information I might find useful? cheers, lance
-
- 16 replies
- 16k views
-
-
ok so ive finally decided I'm going with the ca18det in my ke10 i would like some help with the brake and suspension setup on these ke10 as i know there will be alot of mods. what would be the best brake and suspension setup?? i was thinking of using the s13 front cut brakes and suspension is this the best way to go? i really don't want to go bigger than 14inch rims please help! thanking you in advance!! cheers
-
- 4 replies
- 10.5k views
-
-
does anyone have a roundabout price for this conversion and if its the best choice or point me in the right direction of who knows cheers!
-
-
- 6 replies
- 6.9k views
-
-
Hey guys I'm still new to the 4AGE seen but I've just finished doing a 4AGE conversion on my KE70. Had it up and running last night which made me proud of myself lol Any way on a more serious note, I changed all the fluids in the car today and then connected up the temp sender on the firewall and gave it crank and it started but there was smoke coming out of the exhaust??? I'd like to add that my oxy sensor is not getting a proper reading as it is just at the end of the extractors held on by a bolt as I've had no time to get an exhaust made up but i'll be heading out to get one made up this weekend. Could this be because the oxy sensor is not getting a good reading? …
-
- 2 replies
- 5.1k views
-
-
I have a 2spd automatic ke10 corolla with 70,000 original km in overrated condition I'm the 2nd owner and am very tempted to do an engine conversion ca18det is there any way i can convert this beauty without having to cut her up?? or any engine suggestions without modifying tunnel or wall??? cheers!
-
- 3 replies
- 7.4k views
-
-
what would be the best setup (brakes...ect)for my ke10 with a 7k motor ? do i need to modify tunnel? or fire wall? i have a 2 speed auto in there atm what would be the max power output on a worked 7k NA
-
- 1 reply
- 5.1k views
-
-
Just wondering what radiator members have used in CA ke30/55 ?? Anything bolt in or near to ?. We are looking on ebay at AE series ones some look usable.
-
- 6 replies
- 3.9k views
-
-
hi all I am currently in the process of doing a 4age engine conversion on my ke11 and I am wondering what rubber engine mounts every body uses i struggling to find some small ones, I ordered hilux ones but they are way to big any help will be much apprectiated marty
-
- 1 reply
- 3.6k views
-
-
-
hey, was considering dropping the 4k turbo idea and going for a little bit more power ;) want to know if anyone has put a 1jz or 2jz into a corolla before or thinks it will fit any advice or help is appreciated thanks
-
- 3 replies
- 9.8k views
-
-
hey all just recently got my blacks and want to upgrade my lil stock corolla to a supercharged sleeper, and would really like some help with all aspects of the job from finding the right parts and for how much, to computers and anything else helpful. And even if this would be worth it?
-
- 4 replies
- 3.6k views
-
-
hi Can anyone recommend an engineer in sydney that will pass a ca18det in my ke10???
-
- 1 reply
- 2.4k views
-
-
Hey guys I'm currently putting a 4AGE bigport from an AE82 into my KE70 and I have it all dropped in ready to go with the harness attached and plugged up to the engine. Today I went to go plug in the ecu and I realised that there wasn't a 14 pin plug for the ecu? I'm pretty sure there is supposed to be one as that has the +B1,+ B and Batt terminals that I need power when doing the wiring from what I've researched. Also I couldn't find the 5 Pin plug for the relay located behind the ECU and the 3 pin round plug for the alternator? My guess is that I am missing a loom which is seperate from the engine loom? or is there something I don't know? Can anyone help me? …
-
- 3 replies
- 3.3k views
-
-
Basically the 3K in my KE20 isn't the greatest so instead of doing a recon i thought i might drop a 4K in instead :P Everything in the car is original at the moment (4sp manual by the way) just wondering what problems (if any) i would run into as i am new to engine swaps :( Any healp would be appreciated! Cheers
-
- 4 replies
- 3.3k views
-
-
hi I'm new to this fourm stuff, i got a ke 17 and want to convert the motor to a 4age or 4agze at the moment i have a 4age motor and t50 gear box out of a ae 86, what is the best diff to get? and tail sharft? and does anyone make or sell engine mounts and what other mods are required to do this conversion? thanks guys james.
-
- 3 replies
- 7.2k views
-
-
I have the parts for the motor but need another head for it valve seats came out and it is a lot of work for a slimn chance of servival for a full recovery so I am looking for a good head and cams for my modifide bottom end. I have a 1971 hilux waiting for it to go back in and would like to see it go in this year. like I am asking please if anyone knows someone with the head and cams in good condition to be rebuilt or is rebuilt I am very interested Thank you for your time email please
-
- 0 replies
- 8.6k views
-
-
need info on the wiring for the 4age 20valve silvertop into ae93 engine conversion no one is ever specific about what to do with wiring
-
- 2 replies
- 4.8k views
-
-
Howdy guys I'm new at this forum stuff so bere with me ha. I know it been done plenty of times before but i want to put a 304/308 into a corolla that ive got only for drag an burnout.So what engine mounts-sump an pick up-exhaust manifolds or any other mods. Plus what is the best brake upgrade as well. Thanks any help is greatly welcome.
-
- 7 replies
- 4.3k views
-
-
I AM PLANNING TO PURCHASE AND FIT A 4AGE 20VALVE BLACKTOP HALFCUT INTO MY 1990 AE93 COROLLA SECA SX AND I WAS JUST WOUNDERING IF ANYONE HAD ANY INFO ON THIS CONVERSION TO HELP SUCH AS ANY PROBLEMS I WILL COME ACROSS
-
- 1 reply
- 3.9k views
-
-
Firstly i realise that this has probably been covered numerous times before.. after doing a quick search i couldnt find anything.. Budget is low.... Whats the best and easiest engine to convert in an ae93.. taking out the 4afe and replacing it with something that moves... Thanks a lot Tom
-
- 4 replies
- 5k views
-
-
hi i l finally got my 4age bigport tvis running in my ae71, it runs not bad but every now and then it splatters down low and feels like its choking and idles alittle high, i have the cold start vavle blocked off(big hole in throttle body), check for vacum leaks none, timing is fine, if any one has any ideas what else to check it will be appreciated, and also does any one no of any workshops with experience with these engines in melbourne near the northern suburbs?????????
-
- 0 replies
- 2.2k views
-
-
hi people, i have resently come into contact with a very cheap ca18de with a box :faq: , that ill either be puting in my or my mates ke55. i have a rebuilt celica box in my car and apartently i can use tis so that the shifter comes thru the original hole, so does anyone know of a good engineer in melbourne and a good shop to get an adapter plate made for the celica box. also will the brakes need to be upgraded, i know its a good idea too and will be one day but wondering if a have too any help would also be very welcome, ( please help i'm not sure whether to put it mine or my mates) paul :D
-
- 178 replies
- 118.2k views
-
-
Yo. I am currently swapping my 4age from my ke70 sedan to my panno. The gearbox crossmember bolted up nicely to the sedan. But trying to put it in to the panno and the bolt holes don't line up. Anyone had these problems? Other crossmembers i can use? Cheers.
-
- 4 replies
- 3.2k views
-
-
Hi guys, I know this club is for corolla's, but i'm in need of some help with the lux. its a 1991 long wheel base, singlecab, grinner with the 2y (1.8L), 4 speed manual box :( Want to upgrade to a efi motor and whack a 5 speed box in... Does anyone know if this is possible without changing mounts, tailshafts etc.... and what motor would i be after.. like a 3y..?? costs. etc.... cheers guys Luke
-
- 7 replies
- 3.5k views
-
-
Hi all. I'm a noob to this but have been a long time fan of rwd rollas. looking at buying my 1st one this week, and would like some help with what engine to go for. Tried and tested 4age or a beams engine as I understand these are already rwd orientated and would be and easier conversion. any help wood be appreciated.
-
- 8 replies
- 4.7k views
-
-
ive recently bought a ke70 n lookin at engine conversions.. most popular one is 4age.. i also thort bout puttin a 6 in it for more power.. so commy v6 or toyota 6.. which wuld be easiest n cheapest... thanks :)
-
-
- 27 replies
- 54.3k views
- 1 follower
-
-
Well as the title states... I'm new here :) Ive been reading up a lot on here.. lot of useful info! but what I havnt found is much info on registering a KE20 with a V6 Ecotec fitted. I have a mate who has a gemini with one that is 100% street legal and registered with the V6. Has anyone on here done it with the Ke20??? I'm in the process of building one and thought it would be nice to register it. Does anyone here know an engineer in this field? Cheers in advance! Dan.
-
- 20 replies
- 28.5k views
-
-
Hi guys, I'm in the middle of doing an engine conversion in my KE20, I'm putting in a 2TGEU with a 3T bottom end. I've got the engine sitting in the car but I've ran into a problem where the brake master cylinder is too long and is in the way of the twin carbies. Does anyone know of any shorter brake master cylinders I can use? Maybe Datsun? Cheers, Ben
-
- 4 replies
- 2.4k views
-