AExx Corolla Discussion
1398 topics in this forum
-
Hi, Does anyone have the crank pin diameters (conrod) and main journal diameters of a 4AC crank? Ive tried searching with no luck. Reason being I have a 4AG prepared block and crank, intending on a 4AG build, but might be cheaper to rebuild the stock 4AC at the moment and have something running, rather than something fast and expensive. So really, can I bolt up the 4AC conrods to the 4AG crank? (47.982mm-48.000 Main and 41.989mm-42.000 crank) Cheers, Mark
-
- 10 replies
- 9.4k views
-
-
Hey guys i bought a 91 sx hatch yesterday for a really good price, and everything is gun except the gearbox and clutch. From searching and reading i believe the gearbox is a C52 yes? Its pretty mushy and grinds a bit around 2nd and 3rd gear. What suggestions? Whats a gearbox rebuild or freshen up worth? Should i just buy a replacement and hope its in good nick? Ive got the spare money to spend a little on it, and i was going to have the flywheel lightened while the clutch is being replaced.
-
- 2 replies
- 1.9k views
-
-
I have an oil pressure gauge which goes up to 500kpa (72.5psi). will this be ok for my 4age? I've been looking for ages for the maximum oil pressure for the 4age but can't find it anywhere... I need to know before i buy the sender for it.
-
- 3 replies
- 4.9k views
-
-
Hey, I'm after a wiring diagram for the instrument clusterof an AE71 if anyone can scan one or knows where one is on the net or something. I've searched here and google etc. and havent found anything. Thanks, Travis
-
- 5 replies
- 24.5k views
-
-
hey guys I'm new here, from launnie in tas. ive got a 1984 ae71 csx with stock everything, and just got it serviced today. the guy said the carbie needed some work and that the electronic choke was stuffed. is there any cheap way to fix it, like putting in a manual choke or something like that? or should i get a whole different carbie? any help would be good thanks.
-
- 2 replies
- 3k views
-
-
hiya I have pulled the wiring loom out of my seca to put into my KE70. The question that I have is, The open circuit that is on top of the ecu. Does it proved power to the ecu and fuel pump when the key is turn to the start? thanks Chris
-
- 3 replies
- 2.4k views
-
-
Hi Guys Replacing the distributor in a 4AGE, need some help- the part number on the dizzy is so old can't make out all the numbers. does anyone know of any databases, or any importers that may be able to identify it? its a bigport 7rib. what we're able to read is 22(9 or 0)(4 or 1)00- 5426 4A-GE 11010 (indented) Denso, etc. If anyone knows a good place to source the dizzy that'd be awesome too. Thanks!
-
- 3 replies
- 3k views
-
-
My daughter has managed to damage 3 out of 4 doors on her 1991 Corolla sedan and I have the oppotunity to buy the needed doors from a 1988 sedan. Question is, will they fit ? I know doors are expensive things to design and change and superficially they look about the same but can anyone tell me if they are interchangeable ? Alternatly, does anyone in Sydney have a RHF and 2 LH doors for a '92 model ? Thanks !
-
- 3 replies
- 2.9k views
-
-
Hi, I am new to this, just asking if there are anything out there eg. a turbo kit that I can install to my ae112? If so, where can I find it?
-
- 8 replies
- 12.1k views
-
-
I do not know alot about cars, i am just learning. As most of you know I'm on the lookout for a new gearbox for my red 4age. However i spoke to a guy at work and he said i needed to replace something , can't remember what its called. Problem being gears crunch going into second above aprox 30kmph, every other gear is fine. It will go into 2nd without crunching at around 20-30kmph if i ease it into it and will go in no troubles below 20. Does this mean i need a new gearbox???
-
- 7 replies
- 2.1k views
-
-
bought this lil one knowing i had to fix some things on it including getting the gearbox replaced and the over/under reving fixed. Paid 500, bought it off my brother, 20V 4age gearbox needs to be replaced but my dilemma is whether i will be able to use the gearbox out of my wreck (1985 csx single cam corolla) :P
-
- 11 replies
- 9.1k views
-
-
When i took the car somewhere regarding another problem he said this needed to be replaced. He also said it is cheap to replace. 1. What does it do. 2. can i drive the car whilst it needs replacing 3. how expensive to replace 4 and how hard is it to replace (could someone with a reasonable car knowledge replace it)
-
- 2 replies
- 1.9k views
-
-
hiya, I got a second 4age ae82 and it lacks power (my ke70 will keep up). I have looked at both and the only differences I can see are; Power steering Different injectors Aftermarket fuel filter Factory exhaust I guess all of these could put add up power lose, but to cut the power in half? The tivs was not working, but I fixed it. (vacuum leak). This made very little differents Stuff that I have not tried; Fuel pressure Timing Spark plugs compression Question; Does anyone have any other ideas why it could be so gutless? What colour are the standard injector (one has red and the other grey) I am going to service the engine. I was going to do; Timi…
-
- 15 replies
- 12.9k views
-
-
Hey, she just stopped starting. Turns over fine. Checked all leads/plugs/distributor/coil. Nothing. Now i believe its the fuel pump. Is it fair to just remove the piping from the filter to the manifold, turn it over and see if any fuel is pumped through? Also, could it just be a relay? If so where is it and how can i check it? If the pump is gone, do i need to drop the tank or can i access it from outside somehow, because i can't see it. Thanks for the time.
-
- 3 replies
- 27.3k views
-
-
ok i really need to know whats best for the engine and the power a 32/36 weber or 40/45 weber or whatever brand oh and its for a 4k!!!!!!!!!!!!
-
- 6 replies
- 3.3k views
-
-
hey ive just brought a 1984 ae71 and have been told that some ae86 parts would fit the ae71 and i am in need of new suspension and wanting to no if the ae86 1984-85 shockers would fit my car
-
- 11 replies
- 3.5k views
-
-
hey guys iv got a 92 corolla hatch with 6AF-C engine, 1.4 twin cam. its a carbie, i was wandering, is there anyway to put an air intake with a pod? i don't no nething bout carbies so please don't laugh. lol i would really appreciate any help. thanks.
-
- 1 reply
- 2.1k views
-
-
Hey guy's i recently brought a 3A Racing pod filter off ebay as i wanted that nice pod air induction noise and well yeah tongue.gif I've got a few questions though before i go trying to tear apart my new ae82 and install it... #1 What left over plugs, sensors and so forth will there be once i remove my air box and what should be done with these to ensure my car still runs smoothly ie drill a hole into my 3" pipe and plug them into that such as any sensors ? i really have no clue what needs to be done.. #2 after removing the box where should i run the pod too ? obviously the engine bay as it'd just be sucking in hot air.. so the next spot is up the front but exactl…
-
- 1 reply
- 4.1k views
-
-
Q1:- Convert 4A-C to EFI: I've done some searching and can't seem to find definitive answers, so... How hard/easy should it be to convert a 4AC to EFI, which engine should I get the bits off, approximate cost etc. This isn't an engine conversion thread so I don't want to hear the whole "don't bother, chuck a 4AG* in it" bollocks. I simply want to know what I asked. Q2:- Does anyone around Brissy got a T50 they don't have a use for, in decent enough condition and *cough* cheap :) Q3:- Does anyone have a Ram-Flo filter to fit the standard 4A-C carby they don't want? Q4:- Should I be able to swap the brake booster from my KE panelvan to my AE pane…
-
- 14 replies
- 4.7k views
-
-
hey guys, just wandering if anyone could help me with my problem. last nite, in the wet i was in a 2 lane roundabout and a truck started coming into my lane, i swerved and slid out 180 degrees into a big gutter, the truck obviously drove off and i was stuck there, i have rims on the back of my rolla, they are 16inch alloys and stockies on the front, i hit the gutter with the rear passenger wheel first, now I'm getting a sound when I'm driving its like as if the wheel is buckled or sumthing, i took the wheel off and put another same one on, the sound is still there, yet not as loud. i had a look at the struts, they arent bent, so i don't no what it could be, do u think may…
-
- 5 replies
- 1.9k views
-
-
Hello!!! Since I had my car serviced last, I've noticed that my temp gauge is taking MUCH longer to get to normal running temp, it has been a bit cold weather wise, but it's really quite unusual...for instance, I let the car warm up (it used to be a couple of minutes) and by the time I got to the end of my road, about 300m it's fine, then onto the freeway, now, I run the engine for a couple of minutes and 12 - 15 klm's later it thinks about moving up, to normal operating temperature...whilst it's cold the heater doesn't blow warm air (which I thought rules out a faulty gauge) and it doesn't happen ALL the time, in the last 2 weeks (that I've noticed it) it's happened …
-
- 2 replies
- 2.1k views
-
-
gday do alot of motorkhana work on bitchumin in my 1987 ae82 4a-c motor, and was wondering how the hell do you hook up a hydraulic handbreak to drums?? and also does anyone know if they are illegal or legal on streets??
-
- 4 replies
- 2.3k views
-
-
Hey, I'm new the forums, joined up mainly for this reason but I'll hang around as long as I've got my rolla :P What I'm trying to work out is where the horn is located under the bonnet of the car, I've been looking for god knows how long now and I still can't find it. I've got a replacement, just something better because the one in it is sounding a bit old and worn out, but I don't know where it is to replace. I'm hoping one of you guys (or gals) will be able to give me some pointers as to where to find it, and then how to change it over (although I'm presuming this bit is fairly straight forward). Thanks a bunch.
-
- 5 replies
- 8k views
-
-
hi guys just wondering, i've done a bit of a search but to no avail have i found out what kind of replacement shocks i can use for the front instead of the standard ae71 front monroe gt gas shocks as with my suspension being low king springs & then being chopped 2 coils all round, i'm after any suggestions of a different type ie: rear shocks you can replace with suzuki sierra front shocks....... would anyone happen to know what kind i'd be able to use to stop my front end from bouncing around that little bit to much???? cheers tom
-
- 3 replies
- 5.6k views
-
-
Hey guys, i can remember a year or so ago i downloaded a workshop manual for the bigport 4age off rollaclub and now i can't seem to find it? any ideas where its gone?
-
- 10 replies
- 4.1k views
-
-
ok people i have a ae82 seca its got superlow king springs and new gas ryder shocks.the front shockies bottom out lots over small bumps the back is good doesnt bottom out at all.so if any one has any suggestions about the front that would help heaps
-
- 25 replies
- 29k views
-
-
everyone has been saying that putting a 3K head on a 4K :y: What is the difference if i put a 3K head on and would it change power....etc. Also what model corolla are they off and what engine size are they?(1.2, 1.3, 1.5) Would it be a good idea to put cam ,heavy/dual valve springs and what ever else. And also do they bolt straight on??
-
- 3 replies
- 2.6k views
-
-
hey guys, i've seen a set of luminous dials for an AE112 on modyourcar.com i was wondering if anyone has got these in there rolla yet, and how they look when switched on. ;) they also have dials for some of the older AE's plus suspension gear, like the strut brace i was searching for. any help would be great and all opinions welcome. pics would be awesome if youse have any. Cheers guys.
-
- 13 replies
- 5k views
-
-
just need some help in the way of stud pcd for an ae80 rolla and what would be the bigest size wheel i could fit with out doin any work?? i looked through the website but couldnt really find any thing cheers Tory
-
- 6 replies
- 5.6k views
-
-
Hi guys, I am looking at one of these as a little camping wagon but I have no idea what it is worth? It has 408K on it, and is in average condition, except for the head gasket. Are there any other drames to look for. I cannot find much on the 4AFE but I guess it is the baby version of the 4AGE. Thanking you for any help. Paul
-
- 14 replies
- 3.2k views
-
-
Need to go fatser! what could be some good upgrades other then carby's
-
- 2 replies
- 2.1k views
-
-
Hi guys, Having a bit of a problem with my heater? When I have the heater on, it feels as though the temperature is set at half even though the slide bar was way across in the red section. I had it on for half an hour on full, with the temperature set on red (hot) and it was blowing out warmish air not as prevoiously done before. I am pretty sure the air fan heater thingy is where the globebox is (around that area), do you think there is a problem with that unit or could there be something wrong somewhere else? Thanks!
-
- 3 replies
- 2.9k views
-
-
My son's '92 AE92 SE hatch needs new damping at both ends. For now, I'm interested in what's involved in doing the front. I've been advised that the whole strut is replaced, and is not a job for the handy-person - is this true? Quotes so far have been: $590 fitted or $362 supply only - Pedders; or Monroe $350 fitted elsewhere, with a possible $88 for bump stops. Questions: Are there particular brands recommended (or to be avoided), and what are they? Is it possible to DIY? Are there reasonably priced avenues for repair in the Brisbane area? Thanks
-
- 9 replies
- 6.2k views
-
-
I was talking with justin the other day and he meantion some one saying about another car having shorter steering arms that you can use? Is this true? Also are XT130 arms the same as ae86 (i know there not the same are ae71's) Also wondering if any bodys knows where that webpage is of shitloads of suspention parts and dimentions. Had it in my favuoites for a wile? J.
-
- 5 replies
- 5k views
-
-
hey guys, I've just picked up a Fwd '85 Ae82 sedan 5sp with a 4A-C 1.6l donk for $200. it's also got "SR" on the firewall which as far as i understand means it has a tweaked cam in it? I've been searching eBay for a short shifter but can only find ones that fit '87 forward. is there one made to fit my car? or will this one fit? http://cgi.ebay.com.au/SHORT-SHIFTER-TOYOT...1QQcmdZViewItem also I'm looking for a bit more balls in it and was thinking an upgrade of carby. what would be best with what jets etc? i was thinking a webber but I'm not looking to spend all that much plus I'm looking for something that will bolt straight on with no other mods. o…
-
- 10 replies
- 4.8k views
-
-
hey guys any easier way to get the wheel bearings out without using a big sledge? i know you could use a press but don't have one of those
-
- 5 replies
- 4.3k views
-
-
hey i don't really know too much about exhausts/mufflers and i was just wondering if this tiny hole in the muffler is supposed to be there? ive seen another ae82 with the exact same hole so idk. my mate and i were thinking just a small tac weld to cover it up? anyway just thort id ask to see if anyone has any idea.. thanks
-
- 4 replies
- 6.3k views
-
-
Hey guys n gals. Just something that has sparked my interest. Other than the engine being a 2ac 1.3l in the AE80 and a 4ac or g 1.6l in the AE82 is there any other differences between the two models. From what I can tell they are exactly the same car. Also were the AE80's produced in smaller numbers also as I don't remember seeing much in the way of AE80's around for sale in the trading post, car sales ect. Thanks....
-
- 8 replies
- 6.9k views
-
-
hey guys , the fuel pump in my AE82 twin cam has shat its self , have tried locating it but havent a clue where to find it , sounds like a dumb question but ive never worked on one before . any help would be great cheers guys !
-
- 2 replies
- 2.3k views
-
-
Hey guys Well yesterday I got given a 4age block, crank, and smallport head ;) . The block is one of the early 3 rib types but has been cleaned up and honed ready to be put back together. So i have a few questions for the 4age gurus out there. 1. Am i right in presuming the smallport head will be fine to use with the 3 rib block? 2. It didn't come with a flywheel but can a flywheel from any fwd 4age be used? Its got the 8 bolt crank. 3. Will i need to use the smallport injectors and fuel rail with associated loom or is the bigport ones interchangeable? 4. Are the bigport pistons and rods the same as i believe the smallport had higher compression than th…
-
- 11 replies
- 22.8k views
-