AExx Corolla Discussion
1398 topics in this forum
-
hey guys, just went to pedders and asked them if they had front springs for ae86 struts but they don't and wanna know what other corolla springs fit? ? like are they the same as t18 or what? just wanna know cheeers robbie
-
- 6 replies
- 3k views
-
-
Can anyone tell me if the turbo setup from a AU delivered Sportivo 7AFE will fit a 4AFE engine without to many hassles?? thanks heasp later P
-
- 5 replies
- 4.2k views
-
-
Just started making a strange loud ticking noise when whenever i accelerate. also idle is sometimes low any ideas?
-
- 3 replies
- 1.9k views
-
-
Hey guys!!! as most of you know i own an AE90 with an 4agze with the lsd matchin box, my question you guys is i have this strange Loose grinding noise coming from what sounds like the gear box.. mainly when making a heavy right turn and when i take off from a stan still really hard.. i have put 80w90 gearbox oil with a tube of nulon gearbox treatment in her so i asume that is the right oil.... if any one has any i dear would be great to know what it is. Cheers Tory!!
-
- 7 replies
- 3k views
-
-
Hi all, I've been fixing up my Ae82 corolla and I'm dropping in a 4age in. I am thinking about doing a cold air intake setup and was just wanting to know what setups people have done with their corolla's. There is three ways i am thinking of going with this 1. Small scoop on left hand corner of bonnet 2. Same small scoop but instead on the side of left hand fender panel 3. Pod filter underneath headlight as in drill a large hole under where the fuse box is and have the pod through there. Any other idea's?
-
- 6 replies
- 3.5k views
-
-
I was wondering whether the tacho from an sx cluster should work if I just swapped it with my original non-tacho cluster? sorry if this sounds like a dumb question but my mate did it with his old hilux and it works, Thanks :dance:
-
- 11 replies
- 20.7k views
-
-
Hey all I just purchased a lovely little 32/36 DGAV Downdraft Webber for my AE71 wich i purchased from a good mate of mine, it has a 4AC motor and I have heard that they are a bit hard to fit as the accelerator cable needs to be turned 180 degrees???? At the moment I have the Webber and I am getting the adaptor plate from sprints on Monday but after this I’m stuffed as to what to do and what else I need, if anyone could help with some information it would be much much appreciated. Cheers Ben :)
-
- 6 replies
- 10.4k views
-
-
-
hey guys, I'm doing a 4agze RWD with T50 box conversion and i can get a new flywheel, clutch, pressure plate and starter motor for nothing from a 4Y can anyone tell me if any of these parts are the same as the 4age RWD parts or are they no good to me thanks.
-
- 0 replies
- 1.9k views
-
-
G'day guys, This is my first post and there will be plenty more as I work on my car. What I'm after: I want to upgrade my brake setup - I currently have the stock solids @ in the front and drums @ the rear. I want to find a want to find a way to get some vented & slotted rotors on (4 wheel discs) on the thing. I have already read several guides etc. on this subject both on twincam.org and rollaclub.com and haven't found a great deal of information on it (other that the swap overs you can actually do) If anyone could give me a comprehensive solution on what i could do i'd greatly appreciate it. Cheers Guys, Dean.
-
- 12 replies
- 10.4k views
-
-
Hello, corolla people i've got a 1986 ae82 corolla hatch just wondering what mods should it do? I've allready put a pod filter on it. I'm not sure where i should go next? I was thinking of doing the cams with cam gears and a piggy back computer. One more thing the cam covers are broken i've have taken them off will it effect the engine in any way? thank you and i love all your corolla's their awesome!
-
- 6 replies
- 5.2k views
-
-
I am wondering how the clutch fork attaches to the thrust bearing on my T 50 box. I think its done with clips. if so do i have to go genuine or is there som other type that can get us by. Thanks mundawg.
-
- 1 reply
- 1.8k views
-
-
hey all, just wondering if anyone could help me with some simple performance mods for my 4ac. not looking for a major power increase, just a small amount. looking to do it as cheaply as possible, but I'm open to all ideas. cheers.
-
- 7 replies
- 5.6k views
-
-
So i just tried servicing my auto gearbox ( ae71 corolla 3 speed auto) went and bought service kit i thought it was a BW 35 but the fella at autobarn read a BW 40 from the catalouge, anyway went to go put it in and the gasket was way different. So I'm trying to find out what gear box it would be on the tag that is barley readable it says aisin, borg warner, 0350 andi can't make out the rest. and i looked at the 35 gasket that said it was for fords, and it didnt line up either. So anyone have any ideas?
-
- 2 replies
- 4.3k views
-
-
Does someone one want to list a step by step how-to? I have to put my new one in in the next week or so, would love some guidance so i don't forget something. btw its for a 4age
-
- 3 replies
- 4.4k views
-
-
Hey guys, The fan in my car won't work when switched on to LOW mode. I have tried it with the air con switched on and off, different vents etc but the same issue. It does blow air when switched to Auto (climate control) and medium and high speeds. Anyone want to have a guess as to what may be wrong? thanks
-
- 5 replies
- 2.2k views
-
-
Hi everyone, just had my new Ae82 twin cam seca serviced and checked out by my locale mechanic and it turns out the clutch is stuffed, previous owner must have ridden the pedal alot. Also the cluthch master cylinder is leaking and needs replacing. Everything else is all good aparantly. He quoted me around 600 bucks to replace them both. does that sound about right to anyone? anyone know where to get it done cheaper or will do it for cheaper? lol cheers
-
- 3 replies
- 2k views
-
-
hey guys, got abit of an engine problem here. The car is a 1983 AE71 automatic. New spark plugs, ignition coil, leads, brake master cylinder, front brake pads When i start the car in the cold, i have to hold the throttle down and keep the revs at around 1200 for around 30 secconds before i let it go, or it will stall.. After that, It will drive perfectly, revs out cleanly. (it idle's at 1100 rpm). It wont want to idle any lower, when i adjust the idle screw, or it will splutter and stall. Standard factory setting is 800 rpm isnt it? Okay, now under heavy braking the car will stall. If i brake gradually, it is okay, but if i brake hard (like..normal braking), t…
-
- 14 replies
- 22.3k views
-
-
Hey Guys! i've been a rolla fan, amongst other toyota models, for some time now. i've got some "playing" plans i'd like to get going on... my problem is, i can't seem to find the model code for the transmission used for the older 4WD corollas. my suspicions lead me to believe that it's either the R150F or R151F but i haven't been able to confirm this. was wondering if anyone here could tell me what model code it is and it's gear ratios? i've been searching for a while now and can't find anything. even went down to several shops to see if they were able to supply me with a model code but can't get anything other then a part number. thanks for the he…
-
- 8 replies
- 11.2k views
-
-
Hey guys I'm chasing a speedo gear box drive for my 4agze 5 speed manual... mine seams to keep spaping off the little lug on the lil shaft in side the houseing when i reverse.. i brought a new gear drive off toyota so that part is on so must be something going on in the right angle part of the unit Note: the unit is a 90' degree setup not a straight uint
-
- 2 replies
- 2k views
-
-
Gday all just chasing some info from you AE freaks. I just bought a 92 AE92 twin cam with a stuffed clutch and have a AE82 hatch sitting here for bits and would like to know if the box and clutch are interchangeable?? Havent done a FWD clutch yet but I'm sure theyre the same as all other Corolla jobs, easy when youve done a couple. Cheers, Andy.
-
- 5 replies
- 6.2k views
-
-
-
So after doing some looking around I'm finding that theres not much out there for me. Ive gotta assume someone has done some suspension work for my car. The current suspension has about 300k on it and definitly needs replacing. Id perfer not to go stock sience i don't have power i want something that can handle well. Any suggestions? Thanks
-
- 2 replies
- 2.8k views
-
-
hey if theres anyone with any suggestions id be thankful... i just bought an ae82 1987 sedan with the 4ac engine only 125thou on the clock tight engine... starts fine but then idles so damn rough and seems to lack power driving it... iv replaced plugs, leads, full service oil, air, even cleaned the carby, all that still running like a dog... and also the oil filter thats meant to go on according to ryco is tha z158? however mine takes a z386? the guy couldnt understand why? cheers fellas!
-
- 14 replies
- 10.9k views
-
-
Hi everybody, i am very new to this forum stuff, so please help me out along the way. I have a 1991 toyota corolla hatch AE94. The engine for my car is a 4A-FE. The problem is I'm starting to get a little bored :wink: so i would like to know how to increase the power of my car, even if its just a little. Hopefully getting the extra power with out putting a new engine (e.g. 4A-GE) or a turbo set up in my car. I am very happy with my car, just want a little more power. I don't have very deep pocket either :D still a student and work part time. All your input will be very appreciated. thanks
-
- 20 replies
- 5.8k views
-
-
Hello all, I'm a bit new to the Corolla-hood and I need some direction. I have a granny spec 1987 AE82 CSX hatch with 4A motor and 4 speed overdrive auto. Awesome little car but, just one thing annoys the hell out of me (only 1!). Carby's. Particularly the carby on my 4A motor. Fithy, unreliable things. I've had it re-built twice, checked again by Toyota and various "experts" to no avail (Oh the BS excuses I've heard :doh: ) I still have a pig of a carby with flat spots, surges and flame outs. I've spent far too much money on things that suck and dribble :laff: , so, I want EFI and only EFI. I thought the 4AGE motor would be the best choice but, can it be h…
-
- 0 replies
- 2.3k views
-
-
hey guys!! i dunno if its just me or what but it just seams that my car is not as quick as when i first got her.. i have never owend a 4agze so i have no clue what sort of power they should be making.. the super charger seams to kick in at around 2-3psi and i have about 17vac when off the gas... so my boost gague says... it also seams like that i have to give it juat a tad my now to get the supercharger to start working, like I'm talkin about 500-1000 more revs.... like i said it could all just be me.. and i could just be getting used to a quicker car, any comment would be helpfull any any tips on tuning the motor eg what should the timing be ect, or basic upgra…
-
- 12 replies
- 3.1k views
-
-
Hi all, I'm from NSW, bout an hour north of sydney, I'm probably a bit out of place on a rolla site (i own toranas and commodores...) But I'm just looking for a few basic answers to a few questions regarding my partners AE92 SX seca (4AGE 100kW motor) Sorry if its all been covered but I'm not too crash hot with the jap stuff, I'm more at home with early girl holdens (toranas etc) and later model aussie cars (commodores, falcons etc) then i am with late model jap stuff. I've sat here for a few hours and flicked through a bunch of topics but I'm still just chasing definitive answers to the following- 1) I'm told the 4AGE 16V motors are notorius for drin…
-
- 32 replies
- 57.8k views
-
-
Hi all, I'm pulling out my old 4ac engine and putting a 4age bigport in. I am in the stage right now of pulling everything out and labeling wires, hoses, fuel lines and thinga-ma-jigs. I wanted to know what a few things are called.. Any help would be appreciated greatly, Cheers, Johno :P
-
- 4 replies
- 5.1k views
-
-
Well........ i took my car out for a blast today i was hammering it a little bit but nothing special and when i pulled up to a mates place i realised that there was steam cumming from the exhaust and I'm fair sure its steam its not like a kettel but there is steam and i was a little bit worried. i think that it has sumthing to do with my radiator because thats on the way out and its loosing a whole lot of water but i don't know were the water is going there isnt a leak (that i can see). When i saw i steam i thought o shit the radiator has no water and she has overheated but looked at the temp gauge and it wasnt even half way then i cheaked the radiator and it had l…
-
- 4 replies
- 3.8k views
-
-
Hey guys and girls!! as a few of u know i have just gotten my self an ae90 with a 4agze conversioin in her and ive look around the web and looking a few other 4agze's just about all of them are map sensor models.. is there a great deal of differance between the two?? is the adventure to change my afm to map sensor hard to do, what would i need to do it and how hard would it be?? if any one has any idea of a price it would cost me to do so that would be good to.. Cheers Tory!
-
- 2 replies
- 1.5k views
-
-
Hey All need your advice/opinions My daily driver decided it was going to blow a head gasket on the way to TAFE today and I can't decide what to do. I'm in the process of moving so this is awesome timing. The car is a 1986 cs-x corolla sedan, engine has done around 266,000k's and it leaks oil, body is shit (front right has acco damage), interior is average at best, fuel gauge doesn't work, temp gauge doesn't work. The car cost me 1000 and i doubt before the acco if i would have gotten 400 bucks for it. I have my ke25 coming down here in around 2 months hopefully so i still need a car for the next 2 months minimum so i can't decide what to do and from wha…
-
- 7 replies
- 11.5k views
-
-
wannna know where petrol pump is in an ae82 twin cam 1988 model, need to know asap. I'm a new member. reply or call 0422718596 URGENT
-
- 10 replies
- 3.7k views
-
-
Ive got a '97 Corolla and when you first turn on the car after several hours, no matter the weather, when you put it either in D or R the car jerks forward a bit. But if you turn it on about a hour or so later its fine. It just happens if you haven't turned the car on for about 5+ hours. Any ideas what the problem is?
-
- 4 replies
- 2.1k views
-
-
i'm wanting to get a full set of inner and outer bushings, front and rear, for ae82 twincam swaybars, front and rear. can someone give me a link to a site that sells them? EDIT: ignore the question, I found a great link for urethane bushings: http://www.toyheadauto.com/PerformancePage...hipping._Please the site is great because it has pictures of the actual bushings you will get. just bought a full set for front and rear swaybars, and can't wait for them to arrive to install them.
-
- 4 replies
- 6.2k views
-
-
Ok guys heres the situation i have 4AFE motor in my Corolla and stock power is soo boring i need to do something about it. Now, i don't want to go through the headaches of doing an engine conversion as the car is my daily and i would like to stick with the 16V. So with extractors, exhaust and CAI will i achieve much? And are there any other mods out there that will help increase power? I know it sounds like I'm trying to beat a dead horse with a stick lol but there has to be some way to get good power out of these granny spec 16V motors!! Your help would be greatly appreciated! Cheers! Dave.
-
- 4 replies
- 9.4k views
-
-
Has anyone managed to change their fuel filter yet, i've bought a replacement to put in but cannot for the life of me get the old one out. its mounted in an awkward position on the firewall and theres barely enough room for my hands, let alone tools. i found a repair manual, and it doesnt mention anywhere in the schedualed servicing that it has to be replaced. So atm the new fuel filter is just sitting in the glove box, waiting til i have to get something mechanical done, then ill just give it to the mechanic to put in.
-
- 2 replies
- 5.7k views
-
-
-
Can any tell me where I can get an electronic copy of a AE112 service manual?
-
- 2 replies
- 13k views
-
-
I don't feel like blowing $649 plus the cost of labor on an experiment. So has anyone here installed a Paradise Racing 'Power Pack' on their 4ac or 4a-lc engine? I am thinking about buying the Power Pack for my 4a-lc sohc. I was told by the rep for Paradis that I will just need a custom carb linkage, but that's it's not hard to fabricate. The kit comes with Weber carb, adapter plate, air cleaner assembly (not sure if air filter is included, probably is), and camshaft and valve springs. I would think that I would need the emissions version of the carb also, since my 4a-lc is an emissions version of the 4ac, from what I understand. Would any weber 32/36 carb …
-
- 3 replies
- 16.6k views
-