Car Electrical
Car electrical gremlins/questions? Ask for help here..
959 topics in this forum
-
have read that it drops normal ignition voltage to around 6v for when engine is running and when you need to start car it will double it and bit to get the 13.8v to crank engine. what i wanna know is, is it safe to run with out one? I swapped over a electirc dizzy, and coil into my golf. now i find the dizzy dead so back to points. but i kept the higher power coil, i got car running without a ballast resistor and its fine. but ive read it will burn out points quicker and wear out the ignition quicker cause its at max volts the time car running. True? Also, how does it hook up to coil? Cheers Dan (off to google it more :S )
-
- 12 replies
- 32.3k views
-
-
Alright, i know its not a rolla, but wiring principles would be the same regardless of car. I'm putting a SR20det into a mx73, Using redtop loom and ECU WIred it using this model But still no spark. I hooked up the blue/red wire to the relay as indicated by the Ignitor on the 1st relay. The Blue/red wire has power at the coilpack loom plug. On the coilpack loom plug there are 5 wires, Blue red, and then the 4 wires from the ignitor. These wires change from 0.05-7v when the ingition is turned on. If i rotate the CAS by hand i can hear the injectors firing off. so i would assume the CAS is good. From what i can gather using my multimeter there is …
-
- 0 replies
- 12.5k views
-
-
Hey guys. Few of you might remember the coil igniter problem I was having a while ago. Well thats sorted. ATM, its idles, but barely wants to rev. Coughs, and farts doing it. I unplug the MAP sensor vacuum line and it revs a little better then it does plugged in, but still coughing. Also, unplugging one of the injectors yeilds no difference in idle. It also apears to be getting hot, pretty quickly. Please help. This is driving my brother and I nuts.
-
- 9 replies
- 7.6k views
-
-
Hey guys I have a couple of questions re the coil, I am tidying up my engine bay in my 55, doing a full wire tuck and moving/hiding everything, this includes moving the coil to the cabin. It is running a 4age and an ltx8. 1) will the coil induce a current in objects around it? 2) is it likely to interfere with the computer or stereo? 3) How far away should i mount the coil from the computer? 4) Can i make a sheild for the coil by placing a copper pipe over it and then earthing the copper pipe? 5) are these just stupid questions? Thanks in advance
-
- 4 replies
- 2.7k views
-
-
Hey all Been searching around and can not find anything specific about dash lights being dim. Just wondering if anyone has successfully replaced the stock lights with something brighter? Would these: http://www.ledshoponline.com/automotive_dashboard_bulb.htm T5 dashboard bulbs make a difference? From what I could see when I pulled the dash apart today they look to be the right size. I also installed a VDO water temp gauge today(As the stock one no works). All went fine, yet when I turn the lights on the gauge light flickers slightly. Would this be poor charge from the alternator(got a volt meter and oil pressure gauge on order....speaking of which anyone …
-
- 3 replies
- 2.7k views
-
-
hey, on my ke 36 my first turn of the head lights wont achieve anything.?? I'm new to these cars, should this be dash lights and low in the headlights? also the fuel guage has stopped working! anybody know where i should start looking too fix this problem! does anybody have a wiring diagram for the electrical of this car? cheers
-
- 4 replies
- 3.6k views
-
-
My 1997 Corolla Conquest wont open with the remote and as a result the immobiliser wont turn off which is causing the car not to start. I'm thinking that one of the door actuator is dead which is causing the doors not to open with the remote. Battery is fine. Do you think that a door actuator is causing the problem? If so, how do I determine which actuator is at fault?
-
- 7 replies
- 6.1k views
-
-
Hey guys, My altenator in my KE36 is currently charging at just under the 16v mark. Voltage Reg is screwed. My problem is finding a replacement. The current reg has the part # 27700-1??10 (2 numbers are unreadable). I have the OEX regulator catalogue sitting in front of me and it has no cross reference for this number. Has anybody replaced their voltage reg (Nippon Denso) if so what did they use?? I have two other part #'s in the catalogue which are very similar specs with the same plug and one of these suits "old landcruiser" anyone know if Toyota used an almost universal regulator back in the day?? Any help would be great. Cheers, Chris.
-
- 7 replies
- 8k views
-
-
i believe my car is running like a bag of shit, so i changed the plugs for a new set. is 5.00KΩ to high resistance between ignition leads? thanks for any advice. (i left my workshop manual at work DOH!)
-
- 3 replies
- 2.6k views
-
-
Hi i just bought a new cluster of ebay, and finally got around to installing it. I have a 78 ke55 se, the gauges are a lil different to my original. My main drama is the speedo connection that plugs into the the speedo cable isnt the same as my original..... The original is longer and the newie is shorter and wont plug in or push the pin fully in. Whatr can i do? Also, the new speedo goes to 160km/h when my original goes to 180k...... My fuel and temp gauges don't seem to be working on the original and the speedo gets stuck on 4o at idle there fore I'm going 25-30 k under speed when driving. HELP PEOPLES!
-
- 1 reply
- 2.5k views
-
-
Hey Folks I picked up a Tercel Electric Dizzy (3A), it does not have an external coil (I assume it is internal) and two wires from it, one black and the other black/orange. Any have an idea on how to fit it to my 4AC? Cheers Mike
-
- 3 replies
- 3.1k views
-
-
Hi everyone let me start by telling you what has been going on with my car. I havent had any problems with it up until about a week ago. i was driving somewhere, just a short drive about 5 minutes, and when i tried to turn the car on again to come home it owuld not turn over. the charge light and the other dash lights that usually come on when you turn the key didnt. completely dead. i waited about 10 minutes and tried again and lo and behold it turned over and started no problems. the same thing has happened a few times this week and so i decided to swap the battery for one i know is good. but then tonight i was driving somewhere and had the headlights on, stereo…
-
- 11 replies
- 6.1k views
-
-
Okay guys, I hope you can help me out. I tried starting an ae71 automatic that has not been driven between 4-6 months. Now this is not my car so I don't know its history. Anyway, the owner said the car wont start because it had a flat battery so I brought my own as new century battery. I wired the battery up pumped the accelerator a bit and it was turning over as normal but it wouldnt fire.. So I pulled off the distributor cap and the contactors and rotor button had that white calcifaction build up on them, so I cleaned them up in the hope it would make the car start, but I was wrong. So one observation I made was that the points inside were closed after I contino…
-
- 4 replies
- 4.2k views
-
-
-
Hey I'm after a sparky to come look at my car and fix it up, I know its something small because they were working before and all went dead at the same time. Its a ae92 GTi hatch, checked all fuses and they are all good. Will pay in beer or cash :D Call 0425617228 if you think you can help out. Regards Ian
-
- 4 replies
- 2.9k views
-
-
Hey, just wondering if any one knows roughly how much it would cost to install air conditioning into an ae94 corolla?
-
- 0 replies
- 1.7k views
-
-
Hi all, Ive got a tacho dash out of a AE92 and I want to put it in my AE95 wagon. I have a schematics for the AE92 but require them for the AE95, has anyone got a w/shop manual they can copy the cluster schematic pages for me? cheers.
-
- 8 replies
- 10.7k views
-
-
hey guys, i am currently running a locked 5k electronic dizzy with internal ignitor on my heavly worked 5k. now the problem i have is with the cam i have in it(unknown specs but very lumpy) and the fact that the dizzy is locked and has either no or full advance(diaphram?? has also been removed from dizzy body so can't just hook vacumm hose back up) it either dosnt want to idle at all or idles to high at about 1800 rpm :y: . now i have thought that to to help fix this id throw a points dizzy back in(standard 4k-c jobby), i did that it idled better but the electronic coil didnt like the points didnt last too long. now this begs the question: can you swap al…
-
- 9 replies
- 3.7k views
-
-
hey, as the title sais I'm after the wiring diagrams for an AE80 2AC corolla, if someone could help me out it would be much appreciated
-
- 0 replies
- 2.2k views
-
-
hey peoples . getting more and more frustrated daily . i just completed a 4ac to 4age 16v conversion . i got the wiring harness all connected and all the plugs in . my delema is when i wired up the last pinout out (14pins) i can't get any signal from that side of the computer , its al dead , i checked if theres power from igntion goin 2 the ecu and there is , so my problem is y isnt there power leaving the ecu 2 the motor and gettin things going? ive checked fuses etc etc . can i have a blown ecu , but the ecu was completly running before , is it possible just 4 a ecu to f@$k up like that? what checks can i do , or any ideas u can give me guys would be great than…
-
- 3 replies
- 1.2k views
-
-
Hey guys, in a serious pickle and would appreciate some advice.. Recently purchased an 06 ascent seca from an auction and it only came with the 1 key which is grey and has no buttons... apparently an emergency key ( yes yes I'm a n00b ) after finding out its supposed to have master keys i've managed to get in contact with the old owner of the vehicle who told me he threw both master keys out as he no longer had the vehicle :blush: :P :D so I'm wondering what other ways there are of getting another set of master keys that give me the ability to utilise keyless entry etc. Cheers
-
- 6 replies
- 2.8k views
-
-
Hey all, I have searched the site for an ECU wiring diagram and JDM 86 Wiring diagram but to no avail. I need this diagram to complete my conversion. Is the standard JDM bigport ecu wired the same as anything else or will I have to continue searching for the AE86 wiring diagram? Any help appreciated Cheers, Steve
-
- 4 replies
- 15.4k views
-
-
Hey guys I really need your help to diagnose a problem. My 4AGE has been out of the car for about 1.5 years now. When it was in it all worked, now we can't get spark and the ignitor has power going to both positive and negative on my coil... Why is it doing this, is it broken or is something else stuffed. Also the ignition barrel was customised a bit so a switch was used to send power to everything and a push button installed. It has now been returned to the barrel. Pleas help me as I am trying to get the car registered again and this is really holding it up as there is only little things remaining to re regester it.
-
- 10 replies
- 29.2k views
-
-
Just been having problems with the A/C lately. After pressing either the A/C button or ECON button there's no sign of the A/C compressor turning on. No fluctuation in the rev's, can't hear the compressor. Does anyone know what the problem is? also, is there a downloadable Technical Manual? Cheers Edit. Just wanna clarify that its an AE100 Corolla.
-
- 5 replies
- 20.2k views
-
-
does anyone have a picture of where the piece of wiring goes from the wiper motor my project has no wiring going to the wiper motor at all... any help would be great thanks!
-
- 10 replies
- 6.4k views
-
-
Hey guys, I feel like a noob for asking such a simple thing but after all my work it no workskis. The car in question is my Subaru. Warranty refuses to cover repairs so they told me I have to see an auto electrician. I don't have the $300 I was quoted so i decided to do it myself. I've probed a few mates to find out what is needed and gone ahead and installed it directly to my battery from the boot/cargo area. That one will be used for camping. Anyway my mate told me to run 4mm wire, while another told me to run a 15A fuse. I've plugged it all in and... NOTHING This access panel is for one of the tail lights. I've run the one that come directly out of…
-
- 10 replies
- 3.3k views
-
-
Hi everyone, i tried searching but came up with nothing relevant to my car. My fuel gauge has been working fine till a couple days ago when it started to work intermittently. then 2 days ago it just decided to stop working all together. i have tried earthing the wire that goes into the top of my fuel tank as i was told the gauge would read full if it was not the gauge or wiring at fault. but there was no response from the gauge so i would like to know what else i can check to find the problem as the gregorys manual i have doesnt cover this. thanks Charl
-
- 0 replies
- 2.4k views
-
-
hey guys just need some help i just bought an AE86 ADM with a 4AGE 16v the wiring is a bit all over the place which dosen't make it any easier, but took it out for a spin the other day and it just started spluttering and didn't want to idle any one got any idea what i could do its just had brand new leads, plugs and diz cap fitted, any help appreciated:) Regards Mike
-
- 2 replies
- 3.5k views
-
-
Hi I have 2 12inch subs and a amp, i wanna run some neons with this so that they can either come on without music and as well as be in synch with the music. I also want a switch so i can turn them completely off. I am sort of electriacly able.
-
- 3 replies
- 1.9k views
-
-
Hey guys i've been searching the site for quite some time now, and i've finally got a tacho.. now that i have one.. i have no idea where the RPM signal cable is.. so i can install the beast.. if someone could tell me whether there is a place, or if i have to buy some sensor's or something of the sort... thanks a bunch
-
- 1 reply
- 1.9k views
-
-
Just a quick one Just wondering what causes a starter motor to start spinning but not engaging the flywheel when i connect battery i have checked for loose wires, blown fuse blah blah, starter is wired up fine, just main wire held on with a 12mm nut, and one 1 pin plug. Only thing stopping car from starting atm, Dan
-
- 4 replies
- 2.4k views
-
-
hey i have a 82 ke 70 and my horn and hazards don't work any ideas guys would help a lot thanks
-
- 2 replies
- 3.2k views
-
-
warning - non-rolla question! and a long shot to boot ;) I'm helping a mate get his Crown back on the road after an extended "sitting in the garden looking nice" session. Damn thing won't start and we suspect the fuel pump isn't kicking in. Do any of you likely lads and/or ladettes know where the fuel pump is in a 1989 Crown Super Select? Neither of us even know whether it's in-tank or what. Following on ... I don't suppose anyone also knows the part num? cheers, Slapper
-
- 4 replies
- 4.6k views
-
-
hello i have an electric fan relay out of a ke70 which is 15A.. but i want a 30 A relay...form which toyota car i can find a 30 A relay?
-
- 10 replies
- 5.4k views
-
-
Hey guys, I'm having trouble starting up my hilux. It hasn't been started in quite a while and now doesn't want to fire up. It cranks over but then nothing. It's a 2.4 Diesel and the globe lights aren't coming up when i switch on the ignition. I've checked all the fuses and I've replaced the busted ones but still nothing. If anyone has any experience with these hilux's please help me out. Oh and I should probably mention that I replaced the ignition barrel but I doubt it has anything at all to do with why it won't start. Cheers Jason
-
- 18 replies
- 42.5k views
-
-
I've been wondering about the KE's lights, and whether or not they are at peak efficiency. I see the low beam goes through a relay but the high beam doesn't, so that would be a chance of improvement. The other query I have is- Why does the yellow "earth" line return to the switch?? Why isn't that line straight out to earth by the lights? Am I right in assuming the RedBlack is power to the lowbeam filament and RedGreen is power to the high beam? I fitted one 90/100watt halogen and the daughter said she couldn't really see the difference between the left and the rght... :P Thanks Team!
-
- 10 replies
- 14.2k views
- 1 follower
-
-
Hi all, new to the forum and can't wait to resolve some issues with my 4K. So when I am driving at night with the headlights on, everytime my blinkers auto-disengage after turning, my headlights switch off and then come back on anywhere from just under 1 second to over 2 seconds. It is causing frustration as people get intimidated by me thinking I'm flashing them. My guess is its the alternator, but I would just like to confirm. Thanks!
-
- 6 replies
- 3.4k views
-
-
any ideas on how to hook up a after market electronic speedo????????? fitting a sr20 engine to my ke55 and woundering how I'm going to have a speedo?? been looking a t the speco range of gauges and found a electronic one think the product number is 520-00 how do you hook these up ? has any one got a good solution to this? rather not use my kee55 factory speedo gauge if i can avoid it ive also seen on here alot of custom fitted guages similar to the one I'm looking at how did you guys gett them to work? sorry if these are retarded questions , any help be great cheers
-
- 15 replies
- 39.7k views
-
-
Hey guys really need help does anyone know the wiring diagram for a 1987 toyota corolla CS sedan the diagram in the link is wrong http://www.installdr.com/Harnesses/Toyota-Wiring.pdf, cheers if someone can help me
-
- 2 replies
- 7.9k views
-
-
hey all recently i have purchased a ke10 with an aftermarked immob. and it drove fine for a few days then i stopped driving it for a week and it started again fine, i have since let it sit for 2-3 weeks and when i go to start it i turn the key and all the dash comes up but when i hit the button no crank or any attempt at it turning over. now when i hit the button that should allow me to start it the indicators come on like normal and it seems okay but when i hit the button again it goes spastic and sounds munted (which it never did before) i need to know if i remove the immobaliser is it as simple as tracing and removing the wires from the unit? and is there any…
-
- 4 replies
- 1.8k views
-