KE70 Technical Questions
Technical discussion relating to the xE7x model of corollas. Check the Technical Articles forum for answers first.
157 topics in this forum
-
Hello technological savy people. My ke has the original radio in it and i bought a headunit to upgrade, now where are the wires to connect the headunit from the radio? Ive taken out all the screws around the speedo and tried to take it off, its very thin plastic (I'm scared ill snap it) i have also taken out the housing box where the new headunit would sit to try and get a look up there for some wiring, but no luck. Please help a noob out :)
-
- 2 replies
- 28.5k views
-
-
-
Hey guys Basically I havn't had my ke70 for long, its an 84 cs and done 90,000 k's, but i'm having an issue. When idling, you can hear its at very low revs, and wants to drop out. The gearbox (5 speed) will shudder quite badly. Often in traffic it has dropped out completely, wether i be in neutral or in gear. So I'm always keeping my foot slighlty on the accelerator at all times. Also, when shifting, the car will shudder back and forwards, basically exactly the same as if you were trying to take off in 3rd or something. And when i shift, ill put my foot down and nothing will happen for ages, and when it does happen it does the shuddering as i just mentioned. That happe…
-
- 1 reply
- 25.4k views
-
-
Howdy all, I've had my rolla for a few months now and after tackling the main faults (rear wheel bearings, dodgy alternator and other frustrating electrical faults :rant: ) I think it's time to tackle some of the rust on the body. Namely around the fuel door, a spot on the roof and the bottom of the rear guards on both sides. Can anyone please point me in the right direction as to which sort of sheet metal I should be picking up to use for the repairs? What sort of thickness? Also does it need to have any special coatings? From what I can gather it should be zinc anneal. I had a good search around the forum but couldn't find anything specific mentioned. Than…
-
-
- 5 replies
- 47.7k views
-
-
Hi all, As seen below i've recently purchased another Ke70 but this one has a nasty dent on the front right hand fender. Do any of you guys on here know a way i can get it out without having to get it panelbeated etc? I already tried the GPS Suction Cap thing, but didn't work, :x.
-
- 17 replies
- 51.6k views
-
-
hello , everyone in rollaclub , newbie here . Wonder how to fix KE70 DX round light into my KE70 GL , anyone got any experience for share ? thank you so much .. here my ex-car , but already stolen . KE70 blackbelt with 4AGE 16V . and came back like this .. then now i get another KE70 GL for 2014 project wanna change it to round light and 4AGE 20V blacktop ..
-
- 4 replies
- 181.2k views
-
-
hey guys i have a 1981 ke70 cs, and i want took the lights for my gauges up to the lights in the car. just wondering if there is a wire that all ke70's have? or do i need to go through all of them with a test light?
-
- 8 replies
- 30.7k views
-
-
Can you put chrome bumpers on a slant front ke70? i have only even seen them on flat fronts and i want to convert mine eventually but in the mean time i was wondering if they would fit or if they would even look any good? thanks
-
-
- 12 replies
- 101.3k views
-
-
Hey guys, As some of you know i have some pretty crazy plans for my little Ke70, and while the body is stripped back to nothing i plan to make it as strong as possible!. I Have been carefully studying the corollas frame work as i have been stripping it out and i have come to the conclusion i can likely build a certain amount of extra strength just by adding some material in as bracing in key points of the car. Does anyone have any opinions reagurding this? ill post some pics of some of the points i have been studying if anyone has any input into the matter id really appreciate it! Cheers. Luke.
-
-
- 12 replies
- 42.2k views
-
-
Hi all, Will be taking my 71 to Marulan on the 21st. It has a stock bluetop with pod filter and exhaust. Exhaust wise i have 4-1 extractors, one resonator then one high flow muffler. I have a flange before the diff so i can get a quieter muffler/silencer on there without major hassles. What are your experiences? Will a stainless muffler be quieter than a mild steel? What would be least restrictive on performance? Extra high flow muffler in middle or quieter rear muffler with silencer? these are the rules of Marulan: Test 1: Maintain 5000 rpm for five seconds. Requires a reading of less than 92db when measured 5m directly in line with the exhaust …
-
- 4 replies
- 23.8k views
-
-
i have just bought a new ke70 my question is i have an 86 rt142 corona wagon and i want to know if i can use the frons suspension brakes and all as an upgrade like they do out of the xt130 thanks in advance
-
- 2 replies
- 27.3k views
-
-
I have an 82 KE-70 Rolla with a manual transmission, its a paddock bomb through and through. but the clutch is no longer working in it after a bit of a thrashing it slowly stopped working, the pedals gone really loose and I'm not sure if the clutch is gone or my dad suggested it may be out of fluid when I mentioned it... thoughts on my dilemma would be much appreciated :)
-
- 4 replies
- 22.9k views
-
-
i have reacently got a exedy HD clutch but when i went to install it i t was to big and realized i got one for a sr20det. i have an sr20de out of an s15 (non turbo) in my ke70 so i have a 230mm flywheel. is it possible to change the flywheel to the 250mm one to make the clutch fit? any help of advice would be great
-
- 0 replies
- 20.4k views
-
-
hey guys i have reacently noticed alot of people putting s13 seats into ke70's I'm no mechanic but i am good with my hands and i have a bit of know how and I'm thinking of doing it myself i just want to know if its hard/easy and what things ill have to do any help would be appreicated cheers
-
- 2 replies
- 25.6k views
-
-
Hey does anyone know, or have a manual that states what the resistances are on the ke70 fuel sender at full and empty? cheers
-
- 0 replies
- 20.6k views
-
-
so i jst picked up new rolla 3 speed 1982 when i get to bout 80km-100km it revs really high then kinda drops or i put my foot flat down n it stops, something wrong with overdrivee I'm thinking???
-
-
- 7 replies
- 28.6k views
-
-
G'day, Sorry if this posted in wrong section. Have read every single post/thread relating to camber on KE70 and am wondering why I haven't read of anyone doing the following. Seems simpler, cheaper and easier. They only seem to do it with a S13 strutt/suspension upgrade. Perhaps there is some danger/risk I haven't thought through if doing the same with stock KE70 suspension/steering? Any advice would be welcome. Firstly, it's a bush rally car - stock KE70 sedan - other than worked 4k and locked diff. So stock struts and suspension. I'm going with GH Sigma LCA's. Excessive camber yes, but I don't have to care about legality on the road, just safety in the bush. So:…
-
- 6 replies
- 40.3k views
-
-
hey i want lower my car with coils but in the mean time to i have enough money i want to through so springs in to lower it about 40-50mm, any idea of what springs would be best? or if you have a nice set up with springs and shocks and you think it will be nice please let me know. thanks oh yeah for a ke70 as well, my wheels are 15x8, 0 off-set and I have had my guards rolled if that helps :) thanks!
-
- 3 replies
- 25.7k views
-
-
Hi all, As the above says,I have stripped the paint off the bonnet of my KE70 and there appears to be rust on the bare metal underneath,this rust? was not visible before I stripped the paint off. What is the suggested way to deal with this before I prime and topcoat as I certainly don't want it coming through the new paint. I thought maybe spray with rust killer,let it dry,wipe away the excess and prime but I am open to better ideas if any. Thanks all...
-
- 3 replies
- 20.3k views
-
-
how can i get my ke70 going faster, it has a stock 4k engine with a 5 speed Manuel what is the easiest way to get a bit more out of it?
-
- 1 reply
- 24.8k views
-
-
hey all, mate just bought this previous owner bought it new and got the wheels from factory as an option they look alot like s13 stockers to me, 14x5.5
-
- 6 replies
- 19.2k views
-
-
Hey, Looking at putting coilovers into a KE70 wagon, I am looking to go the S13 coilover route for the front, as for the back. Has anyone welded an S13 sub frame in or done an install like this before. Can someone link me to a thread? Thank you.
-
- 2 replies
- 21.1k views
-
-
Hey guys just chasing some opinions on this fuel setup, for my 4age. It's a surge tank with twin pumps, I also have a Bosch 044 at home previously purchased.. Don't know if this link will work: http://item.mobileweb.ebay.com.au/viewitem?itemId=221065804144&cmd=VIDESC
-
- 4 replies
- 25.9k views
-
-
Hi there my diff broke few days ago, I stripped it and found that my spider gears is broken, what's the best thing for me to do?
-
- 5 replies
- 23.9k views
-
-
jackolla melb vic .....hello to all ke70 people first time back since april , i've got the cylinder- head off my ke70 and would like to know if it is nessasary to replace the head-bolts befor putting it all back together, i've heard of people putting all new head-bolts back on but if it's not absolutely nessasary, why do it . my ke70 is a 1984 model stanard 4kc 1.3lt engin done275000 km.thanks. :clover:.
-
- 2 replies
- 18.3k views
-
-
Hi all, So trying to put my front end back together, any tricks to get the sway bar bushes to work? nut don't fit, should i pull out the heat gun? Car is an AE71 with Pedders bushes, stock swaybar, ke55 LCA
-
- 3 replies
- 18.5k views
-
-
Hello everyone;) I am writing to you from Ukraine, the countries of the Third World, I apologize in advance for the translation, the translator "Google" merciless :) Recently bought a ke70 http://philscarblog.files.wordpress.com/2010/08/p7sda.jpg - photo, but I did nothing about it I do not know, can rollaclub help me (I thought) The question is, how do I subdue the hand brake?) the owner said that it is defective, it was about what that spare parts. ))))
-
-
- 6 replies
- 24k views
-
-
Howdy doody, I'm going to be pulling the chrome trim off the rear window of a KE70 to put on my own and don't know how to go about it. I don't want to bend or break it so I'm asking you guize. Ta, brah.
-
- 10 replies
- 40.5k views
-
-
I am in need of someone who can tell me what the valve clearance is for a 1983 Toyota Corollla KE-70 engine, I believe it is a stock 1.6/8 litre
-
- 2 replies
- 29.9k views
-
-
G'day all, i have a 4agze in my ke70 track car, it seems to run good when i first start it, it idles at about 2000rpm but wont adjust down, when i hold the revs at about 2300rpm it goes down to 1500 and then back up to around 2300 and doesn't stop till i take my foot off or give it more, then when it warms up a fair bit it starts to do it without any throttle and makes a clicking sound as it goes down in revs, the clicking sound is coming from the inlet side, could it be a injector playing up? it also runs a bit rich but i don't know how to adjust it haha, I'm getting a new set of plugs for it, coz the ones in it are old as, could that be the problem too? cheers glen
-
- 3 replies
- 19.4k views
-
-
Had a fight with a sign post the other day. smashed the front grill, bent the radiator cross member, and bruised my pride. Q. as i don't have the car with me atm, is the radiator cross member a straight bolt in/out arrangement? or will i require the services of a panel beater? it was a low-speed collision and the fan only JUST brushes the radiator, so not too bad. any help would be appreciated.
-
- 2 replies
- 20.6k views
-
-
,. ke70 1984 1.3lt hello. hi. first of all thanks to altezzaclub who gave me info about tappet clearence a few weeks ago. my question today is if you please, what is the correct torque wrench setting for tightening head bolts on my 4k 1.3lt engin done 275000km . thanks regards john .
-
- 1 reply
- 23.4k views
-
-
Yo peeps, Just wanting to know; I'm located in Victoria (Australia) and wanting to put some 17" 114.3 wheels on my car.. I tried them on but unfortunately the studs weren't long enough and it was hitting the suspension. Where can i source longer studs and spacers from and roughly what is the approximate price for a full set of studs and nuts. Reason i'm chaisng nuts is because the hole is quite small on the wheels, so yeah. Cheers,
-
- 17 replies
- 37.2k views
-
-
Hey all, Whilst driving at night and while my lights are on, the dashboard lights are going on and off. I have a feeling it's a loose connection for a wire because i can hear it sparking/clicking whenever it goes back on. It generally happens only when i turn or put my indicator on. When it goes off i have to press/play around with my indicator stick until it clicks/sparks back on and the dashboard lights stay on. My cousin that was driving behind me told me my rear lights were also flashing on and off so i think they may be connected to this; Any ideas on how i can fix this?
-
- 1 reply
- 16.9k views
-
-
Hey fellas, I have searched around various places, with no luck, My question is simply this; What steering racks bolt into ke70's, and what effects do they have (ie. length, ratios)? I ask this as I suspect my rack is a little raped, and I plan on doing the s13 front conversion, requiring rack ends anyway, and with a rooted rack would defeat the purpose. Power steering may also be consider as I have the gear with my ke's future powerplant (assuming ps simply requires a pump and lines to the rack and not much more too technical) but ps is not preferred. Or, how much to get a rebuild (in Adelaide) Some links, stories, what ever could help. Thank you all!
-
- 21 replies
- 126.7k views
-
-
-
What's the easiest way to remove the rear bumper. I have minimal tools and fear i will have to remove the fuel tank just to get it off. Must be an easier way. Whats the easiest way to remove the dash? Yes I'm a bit of a noob, this is my first re-build so i appreciate all the help i can get. :blinks: Thanks in advance.
-
- 7 replies
- 28k views
-