General Mechanical
Subforums
-
Specific KE Series Corolla Technical Discussion. Includes KE10 to KE70 models.
- 50.5k posts
-
Articles written by members that need to be wikified.
Please post new tech articles in the main General Mechanical forum. Moderators will move good articles here manually.- 436 posts
3875 topics in this forum
-
I was just looking at a brand new radiator for an Ae86 on ebay and was wondering if that would be suitable for the Ke35 to run a 4age? The outlets for the water look to both be on the same side as each other Any help is appreciated Cheers - Andrew :jamie:
-
- 6 replies
- 5.1k views
-
-
Hey guys, I just have a little question regarding running a reground cam profile in my 5K engine I am in the process of building. Now, I am aware that having the cam shaft reground will have an affect on lifter preload and valve clearances, but what I am unsure about is how to correct this as there is no way to adjust the rocker gear as the 5K has hydraulic lifters, and I don't particularly want to convert to solids. Basically, if the cam lobe diameters have been reduced by x, that means that the pushrods will be now that much too short for the rocker arms, am I correct? :'( So, if I get the head shaved by the same value x, will that cancel out the reduction of t…
-
- 5 replies
- 1.7k views
-
-
hey guys, i am looking at supercharging my worked 5k witch is currently in a kp starlet (i no this is a rolla site but the motors are the same biggrin.gif) a mate of mine has done it to 1 of his 4k's. but whati want to do is, will i be better off running a webber carb and jett it to work as a blowthrough setup, or go for a set of 35mm sideys and make up a custon intake plenum attached to them. the charger is going to be a toyota sc12 or sc14 and is going to be intercooled via a factory S14 silvia 'cooler. i no i am going to have to get a new cam for the motor as the one in it at the moment is just far far to aggressive (will bearly idel it so lumpy but i just lov…
-
- 9 replies
- 3.4k views
-
-
hi all ...i have just put a ke70 speed in my ke35...all went well except the gearbox crossmember form ke 35 doesnt match the gearbox holes on the ke70....what should i do cheers!
-
- 0 replies
- 1k views
-
-
Ok so the T50 is buggered so I've source a W5x series gearbox and its pretty cheap for coming with a bellhousing as well. RWD is normally not my thing so I just wanna make sure I've thought of everything so the process isnt slowed thatmuch. Gearbox with bellhousing -> Check starter motor -> the standard 4a one ok? Speedo cable -> electric/mechanical? interchangable? Clutch -> Still at a loss for this one, need one to fit 200mm 29.8mm centre and 21 tooth. Found out its a bluetop flywheel :) Shifter position -> Holes will need to be cut, both the t and w boxes are long Driveshaft -> Will need to be shortened, use the front half off the w55 …
-
- 6 replies
- 1.8k views
-
-
Is it possible/advisable to make an intake gasket out of gasket paper?
-
- 2 replies
- 1.3k views
-
-
I no i must sounds stupid :jamie: and prob has been posted somewhere in here but i can't find it. With the ke55 leaf springs i tried to flip the main leaf and i don't see how it will fit back in?is there a special way? has anyone got any pics on how theres is? cheers
-
- 2 replies
- 1.7k views
-
-
quick question: what is this? i was guessing aircon. Anyways, will it matter that it doesn't have belts running on it when i take it in for rego? thanks
-
- 2 replies
- 1.1k views
-
-
hey all, my cable from the clutch just snapped off last night, just at the point where it goes through the firewall. so i need a new cable for my 20. can i only use a KE2* one? or will a ke30/ke55/ke70 series one fit? my mate said i can have his ke70 one, so would be cool to know if i can just use that! cheers for any help or a quick reply :dance: wanna get my car back on the road. - nick
-
- 2 replies
- 1.6k views
-
-
on friday I'm getting a full 2 inch exhaust on my rolla is it gonna be worth while getting it there going to remove the cat and go 2 inch straight threw but if its too loud there goign to add a hot dog all up its its 90 for the exhaust and 60 for the dog if required is it worth it
-
- 11 replies
- 4.3k views
-
-
I just bought a ke70 wagon, the first thing i want to do is stiffen the suspension up. Any help would be great. Still would love to know where or if anyone can stiffen the rear of my wagon sometime for $$ of course. EDIT: Sorry found it in the FAQ, thanks :\
-
- 3 replies
- 2.2k views
-
-
hi guys new to rolla club don't know much about 20v's heres my story.I got a corolla ae82 twin cam with a 20v silver top runs drives perfectily exept after it warms up if i give it a hit into the high rpms when i pull up the idle will be very ruff, low and alover the place but if i switch off the car and turn it back on it is fine? also a bit hard to start in the morning and cuts out at 7200rp/m. any help will be apreciated the poor thing has been runing like this since i bought it afew months ago. also forgot its runing stock ecu
-
- 2 replies
- 1.7k views
-
-
anyone have a clue if its easy to swap the diff centre for a ke70? and how long would it take cheers
-
- 3 replies
- 2.1k views
-
-
does anybody know a car that has a accelerator cable that is about 30cm shorter then the stock KE70 one. my carbs are on the other side now and its way to long. cheers
-
- 3 replies
- 1.4k views
-
-
hi guys, thinking of putting a t series in the 55, blown one bw already and i think this ones on it way out do the diffs have the same tail shaft bolt patern thingo? and if i got a lsd from a ae86 would that fit in a t series form something like a ta22 or ra23?
-
- 4 replies
- 2.2k views
-
-
Hi guys could someione please help me, I'm having trouble with the idle on my 4k. currently it is stock except for full exhaust twin carbs and extractors. The trouble i am having is that the idle will never stay at 1 point it seems to stick when i rev and then will randomly drop down when it feels like it, usually very inconvenient times. first i thought it would have been in the throttle cable or linkages but its not, then someone said it would be the dizzy balance weights, so i fully stripped, cleaned, greased and rebuilt my dizzy, now the revs don't stick as frequently but everytime i turn the idle down, when it does its random drop to what i presume it should…
-
- 3 replies
- 1.6k views
-
-
Guys I have a 5 speed box from a KE55, what do I need to do to the box to make it fit in my KE70? The KE70 box is longer and is only a 4 speed... ive had a look at the Knowledge Base and it mentioned that 4 & 5 speed extension housings arent interchangable to each other. Does it mean though, that I can put the 5 speed KE70 extension housing on the KE55 5 speed box and fit it into my KE70? are the front part of the boxes the same.... thanks
-
- 8 replies
- 3.5k views
-
-
hey guys just wondering does the bigport 4AGZE have a 7 rib or 3 rib block and does it have oil squirters
-
- 5 replies
- 1.7k views
-
-
hello want to strip all paint from some hanging panels to begin body repairs what is the best process? acid tank/chemically strip OR abrasive blasting ~ sandblasting, soda, glass bead, plastic garnet.... what is the best? where in melbourne can you recommend which is good service and price not too steep?
-
- 9 replies
- 2.2k views
-
-
Hey guys and girls. just wondering if anyone could tell me wether a sc12 charger from a 4age can be used on a twin carbed 4k?? they goin pretty cheap at the mo and I'm keen to get one if so, could someone please tell me how it is done and even better show pictures of people who have done it??? thanks guys. Jono
-
- 4 replies
- 1.5k views
-
-
hey fellas... ive put blocks in the back but now its time for the front. instead of buyin new springs lowered. what else can i do besides choppin the origional ones?? let me know.. cheers guys
-
- 5 replies
- 3.4k views
-
-
Hey all, in the process of (well trying to...) change shocks and springs in my KE70 front struts. Both struts are out of the car but I'm damned if I can even start to dismantle them. I can't crack the top nut under the dust cap. Trying to do so just turns the shock absorber. Is there a trick to stop the shock turning or is it more a case of using a rattle gun or some such? I'm sure the whole process is fairly simple I've just never done it before and gregory's is of very little help. Any ideas greatly appreciated.
-
- 14 replies
- 7.6k views
-
-
I have a '87 Corolla hatch. I love it so far. But! I need more power. It seems to lack speed pick-up, I struggle to get to 80 uphill, and as I do a lot of hills driving I need a bit of grunt. I don't want to spend a awful lot. So idea's are appreciated. Thanks, Tim.
-
- 26 replies
- 8k views
-
-
hey i have a ke20 and it had a slight front end collision and messed up bonnet, front grill and left hand quarter panel, is it posable to transfer parts from a ke 30 onto the ke20 or are the different. advice needed asap as i have rego coming.
-
- 5 replies
- 1.5k views
-
-
hey guys, I'm currently running an sr20 in my corolla its impossible to to handbrake into corners as the gear box sits quite a way back, and when in second its practically above the handbrake. any hints on what i can do to shorten the handbrake. i know its been done before. though i couldnt find any real help info on it. cheers
-
- 6 replies
- 2.7k views
-
-
Hello, I'm a newbie to the whole cars scene, well relatively, i owned a prelude before i purchased this corolla. i just purchased this short shifter, cause i thought that it would be easier to shift gears in, cuz currenty when i chuck it in second, it gets stuck before getting in, and its really annoying, makes me look stupid soo i purchased this short shifter off ebay, and i want to know if it would make it easier to shift gears in, my current shifter has been cut, to be shorter, but i thought short shifters are able to make changing gears 50% more easier or something. i really should of asked here before purchasing it... :lol:
-
- 2 replies
- 6.7k views
-
-
I have a 2 door KE-30 Corolla with the 3K-C engine (1200) and was wondering if there are any 5 spd gearboxes around that will drop straight inplace of my 4 spd box?
-
- 4 replies
- 2.3k views
-
-
Found this on ebay.... http://cgi.ebay.com.au/Toyota-Celica-2T-3T...1QQcmdZViewItem If you look at the welds on the mounting flange to the head in the first pic, they look pretty ordinary compared to the other welds. Anyway, what I'm thinking is that this manifold was orinigally made for an SR or CA, then had the flange cut off it and a T series one welded on!! So for anybody interested in turboing a T series motor, it looks like they have the same exhaust port spacings as a Nissan motor! Heres an SR one..... http://cgi.ebay.com.au/SR20DET-TURBO-EXHAU...1QQcmdZViewItem
-
- 11 replies
- 3.1k views
-
-
Hey guys, I have looked around and i can't seem to find much. just wondering, where abouts do these lines hookup to? these three lines seem to all go into one.. So what do these lines do? and what are they needed for? and what do you suggest i do? (its not going on a MR2?) and heres the flooding of photos.
-
- 2 replies
- 3.1k views
-
-
-
Hey all, first of all my 4k keeps misfiring at high rpm wen i stab the throttle and occasionly wont start or dies at low rpm, the dizzy cap looks pretty foul so I'm gonna get a new one tomorrow, but if not does anyone know what the points should be spaced at, my points are relatively new but may have moved. and as a second question, the vacuum advance, can someone tell me where the hose should connect, i have it connected to the dizzy and to sumwhere near the carbs, but not actually on the carbs, I'm running a stock twincarb setup, but with 4k carbs rather than the 3k ones, can someone please tell me if thge vac advancance is supposed to connect to the carbs, if so, w…
-
- 2 replies
- 1.8k views
-
-
just about got my engine started yesterday and realised the carbs arnt getting any fuel into them. pump is working and it has pressure. it doesnt have a choke so could it be that the fuels not going in cos there cold? any help would be great
-
- 2 replies
- 2k views
-
-
hey all, recently purchased my first ke20. now to stopping time in this car is a lil slow for me haha and i really wanna swap out the stud patterns to 4x114.3 for a more variety of wheels as i don't wanna be getting sets redrilled! now after doing a search on here, reading the FAQ and a lil help from benzo ;) i couldn't find the answer i was after... FRONTS i want to know if a can just swap out my front ke20 struts with ke55/ke70 struts or even ke30 if need be... to get the new stud pattern and a larger brake, is it a straight swap or will there be some modding? and will if fit onto the ke20 lower control arm? or is there another way i can upgrade...? REARS …
-
- 1 reply
- 3.9k views
-
-
I'm researching an engine conversion and was wondering if the 4a-c comes in any rwd rolla's? I thought they came out in the sprinters but not sure. I'm guessing they're not an easy engine to find. Any help would b good.
-
- 2 replies
- 1.8k views
-
-
ok guys ive got a ke38 p/van with a 4afte, thats a 4afe with a turbo fitted not a 4efte. any way i wana upgrade cause i no the 4afe has sh!t internals i got my hands on a 4age out of an ae82 i believe this is a big port motor?. and now to my question which is the best motor to turbo the big port the small port or the GZE also reasonings as to why they are better/different would be great thanks Duggy
-
- 7 replies
- 2.6k views
-
-
Hi Guys Does anyone know what if any other engines share the same intake manifold pattern as the 4AC. Wether it be datsun engines, other Toyota ones etc..... Thanks Mike
-
- 12 replies
- 18.9k views
-
-
Hey, I'm wondering if an 4afc gearbox from an ae92 corolla would be compatible with the 16v 4age engine? thanks i have searched around to find the answer, and all i seem to find is RWD conversions. yes ive used google too :)
-
- 4 replies
- 2.3k views
-
-
Hi from Ireland.. Any idea what this t50 ? is from ...year/model/engine-size (disregard bellhsg/adaptor ! ) Celica ta22 looks different.. Thanks for any info.
-
- 8 replies
- 6.2k views
-
-
well i've been looking around for a wile and seen a decant package http://spoolimports.com/content/SPOOLCONRO...TONPACAKGES.asp SPOOL 4AGE conrods and WISECO Forged Pistons just wondering has anyone had any problems with these two brands
-
- 16 replies
- 6.9k views
-
-
wen i bought my Ke70 in 2006 it came with a 4k block in the boot however the motor in the engine bay is a 4k-u with the dished pistons. ill be keeping one of the blocks and getting bored out etc. anyway my question is would it be possible to put the flat top pistons in the 4k-u block for better compression or would they hit the valves or cause any problems? EDIT: i will be putting the original 4k head back on aswell
-
- 8 replies
- 10.4k views
-