General Mechanical

I've recently got my hands on a set of twin solex side draughts for the old 4k and hunting someone to balance/tune them up in Brisbane/any of you feel like earning some beers :P. cheers guys! On another note has anyone else heat wrapped their extractors below twin side draughts before, and has it made a significant difference/is it worth the effort. Thanks again -Kim

Hey ive got a 83 ke70 dx thats running shit ive worked out that its the main jet being blocked thats causing the problem can anyone give me advice on how ta clean out the jet my self easily?

Been friging a round getting lights working again all working now but reverse lights. I ve pulled the switch out of the box hooked it all up works great when you push the switch manually. S o what or how does it activate in the box. It has a small pin on the end of the switch which goes in and out. Any one have a pic of how it works?? Hopeing not to have to pull it out again. T50 early ta22 on the mighty 4k . cheers rob I

Read this right through so you know you have the tools to do it before you start! Bits of pipe, grease gun, a solid hammer....! This is a straightforward job, well technically straightforward and simpler than changing a distributor, but it does need some mechanical hammer work! A side takes about 1-1.5hrs without hurrying. I did one a day, no rush. First, buy two to these. Mine were for my Corona LCAs, I don't know if the KE70 etc are identical, but this part number fits Corona, Celica, & KE Corollas in theory. Get organised- I have a floodlight, several square of carpet to sit on, and I keep the tool box nearby. I get out the tool I want, use it, then p…

Has anyone got one of these welders? Looking to just do small rust sections and a little light fabricating. Any reviews or feedback on this mig would be a great help.http://m.supercheapauto.com.au/Produ...-140amp/295863

I'm from the melbourne region of victoria and want to know if anyone has bored out a4k to take 5k standard replacement piston heads and toped it off with a ported 3k head? Also a good place i could find barnd new pistons and head for a good price.

Hey guys I currently have a very weird issue in my MS47 Crown. 2 Weeks ago I jacked up the backend and removed the tail shaft to get rebuilt, the chassis has been sitting on stands for a couple weeks with the diff hanging down as per normal. I got my tailshaft back today, it was retube'd and balanced. Sat the car back on the ground and for some reason the back end is sitting literately 3 off inches higher than previous. How on earth does this happen? I've taken it for a drive, everything looks and feels normal, shocks are not locked or anything silly, why would it be sitting much higher?

Going down hill, hard brake, bam foot to the floor. Right rear wheel cylinder spat it's seal. Replaced it with a brand new one, didn't do the other side because I cbf'ed. Bleed up, go down street to test it, bam the left rear goes. (Karma). Replace that side too.. And this is what confuses me, start bleeding the brakes with my brother pumping the pedal up when all of a sudden the brand new right rear cylinder pops. Back to square one. Can't work out why it would pop a new one? Read through a couple threads and this is what I've put it down to. 1. AE86 JDM Brakes up front somehow causing the brake bias to be out and too much pressure going to the rear thus blowing …

I'd like to record a few things like suspension travel in the rally car but have no idea about how to go about it. I could rig up a mechanical system to get maximum compression over a rally stage, but would really like something to record 10 or 15minutes worth of movement. Then it will be G-forces, steering input, pedal movement.. I can see this will never stop! So, if anyone has any ideas on how you record data, store it and display it later I'd like to know. Farmspec of course, I could go and spend a couple of hundred thousand dollars and buy the commercial packages, but I'm sure ingenuity can do it. My kickoff point would be an infra-red distance meter fro…

The Girl's KE70 has a split in the top of the passenger's rack boot, but KE70s aren't listed in the parts book the shop has, it is all AE Corollas. Does anyone know if the rack boots are the same on the AE86 & the KE70?? I can't see why Toyota would change them, but there are differenmcs in the racks aren't there?? Thanks

Hi, Currently under going a diff upgrade in my KE15 and when I removed the stock diff I pulled the leaf springs off and the original saddle pads were worn out. Saddle pads: http://www.mustangsplus.com/xcart/images/P/15012lg.jpg I have done some reading and found a few places where people suggest throwing them in the bin. Why...They say it tightens up the rear end for better handeling. Now if I run leaf spring directly in contact with diff you would have metal to metal wear.. With pad would stop this.... So I'm in two minds find ones that fit and get new ones OR don't install them and have a better rear end feel etc. What are other peoples v…

Hi, I've just bought my first corolla and was hoping to find a 15 inch steelie that would fit?

hey guys iv got a 4age 20v (silvertop). my timing belt is almost done for. so i need to replace it. however the pully system is marked incorrectly (when i got it dyno'd it said 40 degrees out) when that is impossible to run without blowing as the tuner said.... so when replacing the timing belt how do i do so correctly, also if i replace the whole pully system how can i Remark the right degree'z etc ! Thanks Owen :)

Hi all,was hoping to get some advice on a problem with what appears to be a gasket that goes between the inlet and exhaust manifolds which is partly missing (see photo). I have heard that you can get some exhaust repair paste that could potentially be a quick fix, but thought i would see if anyone else has had issues with this before (i haven't been able to find much info on this gasket, even the workshop manual i have doesn't seem to mention it in the inlet/exhaust manifold section). Thanks in advance

Hey there guys, I'm looking to achieve more lock out of my Ke70, so far Ive done the following steering modifications.. T3 - Front Lower Control Arms. T3 - Tension Control arms. T3 - Outer Tie rods. T3 - Ae86 Power Steering arms. But I'm still looking to gain more, so i'm wandering what possible steering rack swaps are out there with the use of the stock ke70 engine crossmember? Any and all help is greatly appreciated, thanks!!

Hey there, I've got a TA22 that I'm upgrading the brakes on (4 pot hilux calipers and XT struts!). To make these work I've also got a mitsubishi starion mastercylinder. Unfortunately the master cylinders reservoir is in the way of the vacuum hose. anyone have any smart ideas? is it possible to buy a valve with an outlet on a 90 degree bend? Cheers Ash Oh and on a possibly unrelated note, if I push my brake booster rod thing to the side (hardly any force) I can hear a sucking sound, which makes me think that the seal is pretty trashed?

Hey guys, I bought a diff off one of the guys who was parting a car out on here a few months back now ( can't remember his username).. When I went to pick the diff up I was told by the guy I bought it off that he had removed it from the ke70 sedan which he was parting out...on pickup though I realised the diff had disc brakes on it....( to my knowledge no ke70 came out with disc brakes). So my question is, is there anyway to identify what the diff is out off as I want to buy new brake calipers for it to rebuild them as the cradle from one of the calipers is missing.. It's a Borg Warner diff with disc brakes, there is only one number on it it is 0570-02690…

Hi people I got a set of deep dish rims of a Gemini and I really want them on my rolls plz if anyone has some advice plz need help

Sup. I have been blessed with an almost rust free shell, my engine bay managed to soak up all the rust... I have been attempting to start the repairs my cleaning out my cooling system however, shortly after I changed over my radiator it sprung a leak. All my hoses and everything aren't leaking and it's a bit of a bugger to trace back. I'll bang up some photos and if you could give me a hand identifying/tracing back the leak. Having no actual cooling problems while driving, engine is still strong and stays cool. It's dumping a considerable amount of water/coolant even though it's just a consistent drip. There is no leak when the car is off, only when th…

hey guys, i just acquired a st141 corona the other week, lowered it and bought 16x8 -0 steelies and they stick out of the guards a little, just wonder what upgrades i could do to get some camber to bring them in without flaring them lots? any LCA's bolt in or can i use s13 camber tops with my stock struts? any information is appreciated cheers!

Okay so My 4k dies out every time I do the smallest skid When I open up the engine bay I can't see any fuel in the lines some I suck some trough to get it gaining again but I want to have it working right I've replaced the fuel lines and filter in the engine bay Any ideas on what I is Fuel pump maybe ?? How do I check of the fuel pump is working ?? Upgrade fuel pump ?? (Ke55)

Hey guys. Tuesday morning when I was about to leave for work my sev died whilst I was warming it up. It will turn over but won't fire. Got the RAA around last night to see if I could get a diagnosis, he told me that my fuel pump ha packed it in. Got a new pump from Bursons today, the pump itself is exactly the same as the one on the motor at the moment, except it doesn't have a return line. It has the hole where it should be but it doesn't lead to anywhere and the inside of it isn't threaded. But it came with the necessary return line fitting. Have I been given the wring pump?

Can anyone possibly identify this random chunk of metal which fell from my 4AGZE??

Ok here we go! 5k block,dished pistons machined to flat tops,block decked to suit,4k head,isky chevy lifters,430lift cam,fully balanced,datsun 12a push rods,new oil pump,all new bearings big end,mains,cam,all meassured 1.5-2.5 thou clearances. Now for the problem this is the third cam & lifters we have put in in 12 months all been the same and getting very pissed of. Start up cold 60-70 psi oil preasure once warms up drops back to 8-10psi at idel 1000rpm. Running Penrite 25-70 extra 10 oil,has any one out there had same/similar issues as this? would like to here from you so as we can sort this problem out. Cheers :- Stuart (Thomas dad).

after aftermarket head studs/bolts for my 4k. replaced head gasket and found one of the bolts was cracked.. Need my car to be running by Monday 15-04. located in North Brisbane, i have called around and have found nothing. cheers

Found these, http://www.precision...=41201&EID=4443 Seem cheap but they come in the .060 i was looking for.. Has anyone used them before? or the Precision site? They have a lot of 4k stuff

hey all, i know theres threads out there about sigma ( GH ) lca's into ke70's and stuff.. but i can never find much detail.. one thread iv seen say they fit straight in.. another says you need to re-drill the sway bar mount.. and more say about the sway bar + ball joint is tapered. if anyone reading this has done the conversion themself, can you please give me some info on what you did, and what needs to be done? also too, what does it mean by the balljoint is tapered? in what way is it? thanks alot! dan

Hi guys been reading through this forum for a while now gathering information for use on my sons speedway sedan ,I found a topic on rebuilding a 3k and the member who posted it did it very well with plenty of detail but I was on my laptop when I found it and now my laptop has died I can't access it and havnt been able to find it again hope someone can point me to it or the original poster may even point me in the right direction Thanks Darren

Hey guys, I have a 1966 rt40 corona, the battery was pretty old and sometimes it wouldnt fire but would turn over when i turned the key Got a new battery for it 2 days ago and it starts fine now. New problem - now with the new battery, it feels like it is leaning out pretty badly at low revs and it jolts and like chokes sort of around corners on low revs when you put your foot down a little bit. did not do this before^^ Car - 1966 Corona. Engine - 2R single carb, 8v. any help would be sick!

I have ke55 borg warner diff in my ke20. Its starting to get all harmonic around the 100kph/3000rpm range. Its fine under acceleration and braking. It occurs specifically cruising in 5th gear at that speed. Sound a bit like a washing machine. "brrrr brrrr brrrr brrrr". Just like that! It appears to have a lot of backlash and it 'clunks' when you twist the tailshaft backwards and forwards. As this diff has the ke twenty spring mounts fitted id like to use this diff housing. What are my options in regards to replacing the diff centre and how hard is it? Will the centre out of any k series bw diffs fit?

After installing my AFR I've noticed that the carb leans out really bad when you jump on the throttle (like to 21 AFR). I previously thought it was bogging down to over fuelling but obviously not. If i put the choke on about 1/4 it solves the problem but idles rich, usually it idles stoich right on 14.7. So I'm thinking it might be a partially blocked jet in the secondary throat? I'm not very experienced with carbs so some input would be great.

Ok I am so lost, I have a failing axle in my TE38 and I needed a replacement. So I visited the junk yard and pulled an axle from an Ra40 ST and I can't FIND ANY INFO! Weird thing is in order to gain access to the diff you have a cover on the back you remove and the spindle snout is actually a part of the axle. It's much larger than my stock axle but I can't find an lsd until I can identify this axle. Please help

Hey guys somehow my 5K has snapped all 6 flywheel bolts clean off, does anyone have any idea where I can get some stock replacements? I don't want to use the old flywheel bolts I have lying around, I would rather start with a new set. Tensile strength has to be correct of course.

Hey guys I'm in need of a new starter motor for my 5K, what options do I have? I have a 3K one lying around but it seems that the mount is smaller than my current one? Am i just nuts?

I keep coming up against the questions Do you want the power steering crossmember or the non power steering? I have no idea i have bought a blacktop 20v for my ke70 and I'm assuming I'm not going to be installing PS into the ke70 anyone help me quickly problem shoot this I've searched a few forums with no clear answer cheers jack

Hey guys I'm wondering if anyone on here would be interested in helping out and modifying some seat rails to fit my ke70. the seat mounting points are from inside points of the holes. 13" apart left to right and 10.5" front to back.

So a few days ago, the diff just locked up as i pulled out of a street. Felt like the hand brake had been applied. Then it unstuck itself once i restarted the car and everything sounded fine so i drove it home. This morning it happened again while on a light corner and now its definitely stuffed, bad noise and feels like its unbalanced... Is this a common when the diffs get abused? I'm assuming I'm going to need a new pinion and center?

Hi all, I'm in need of a carby tune on a dyno. The carburetors are Mikuni CV ITB's (off a GSX1100R I believe) and they're strapped to Phil's twin cam 4K. They're currently running very lean due to changing the air filtration system and it looks like it's gonna need a whole new set of jets/needles to be selected. I need to know two things: Is there someone around Brisbane who is capable of getting these just right, and what am I expecting to pay? I've been told it's not gonna be cheap, but I'd really like to know how much roughly it will cost. Thanks!

From memory someone told me an early celica one will work, has anyone actually done this with a 3T or 2tgeu? cars in at the mechanics and i've gotta source it before they install it..

Hey all, I have searched everywhere under all the search tag combinations I can think of but can not for the life of me find what I am looking for. A while back I came across a forum post/thread where someone gave a really good illustrated walk-through for doing your own acid washing at home. I can not for the life of me find it anywhere. If anyone has a link to it can you please post it in here. Just finished stripping the engine down and now the fun part of building it back up :-)