General Discussion

I need Toyota 7k-e engine wiring diagram or service manual.any one? Please help me Thanks

So my KE70 will need to go in for MOT to get its documents. Having read around it seems like the lights are awful - some bulb need replacing. I tried to find more information - ideally I'd love to go to LED (even angel eyes) but I don't know if that's possible so maybe at least halogen, having done some searches on here I am confused as to .... A) where/what bulbs to buy for the rears lights and indicators B) What are my options for front light replacements/bulbs

Buen día Tengo un TE72, tengo la interrogante de como se comporta la luz indicadora (fasten belts) según con el diseño original En mi auto pongo el motor en marcha, la luz enciende pero pasado unos pocos segundos esta se apaga sin importar si los cinturones están o no abrochados Y no sé, si dicha luz debería apagarse hasta que los cinturones se abrochen. Podrían ayudarme a despejar la interrogante?

I don't know much about this car except it is a second owner car. With 47000 original miles my question is simple is it worth 1000 dollars.

Hello. I've recently replaced my Pcv valve and wondering which way to goes. I bought a fuelmister branded one and there is a short side and a longer side.

All, here is the information I was able to gather. KE70LG-EYKPS 4K KE70-5020888 033 TRIM = XD21 K40 U312 B11 any information will be appreciated. Thanks, Vagomundo...

hey everyone, so I've installed a new tacho instruments cluster into my ke70, it had the good'old quartz clock cluster, and everything works, but the fuel gauge, I don't remember if the old one worked (still have in just encase there is part failure), but I've taken out the rear tail-lights cause I'm doing rust repair, and I noticed that the fuel gauge wasn't moving and staying in the off position, when the car is running, all the other things in the cluster work cause Toyota just used a standard wiring loom for all KE70's. so the question is, does the fuel gauge wire run though the tail-lights wiring? not 100% sure. and I can't find a wiring diagram that says anyth…

Hey fellas ive recently brought a ke70 with a old tired stock motor I'm ripping it out am thinking og putting a 4age motor in just for my first attempt of a conversion is there any good sites i can buy one ready with gear box and computer i can get delivered

Its doesn't give a spark but i change condencer and module coil its still working fine what can i do please help

Hi does anyone know from what car make front right hub will fit ke70. Having difficulty finding one.

Hi folks, iv a 81 ke70, I'm told that I cannot just get the twin head light conversion, I need bonnet,wings and front panel .. is this correct ?

I really want to learn more about that powerfull engine,and when i say how it feels,i mean stock or modified,and if it is better than 4A-GE or a 7A-GE(With 20v and Crina's blocks,just like Keiichi's).And what do you thing is better for this engine,turbo,carbo-turbo or EFI turbo?

Hi, trying to find another set of front mud guards for my 82 corolla. Australian car, with very unusual mud guards on the front. Pictures attached and any information very much appreciated. The logo seems to say "amily"

Hey guys I'm looking for someone in SA (preferably Adelaide) to help me install a full manual conversion in my old reliable. I've got all the parts ready, including a bunch of extras I can't wait to get in (air con, ae71 quad headlights and more) Even if you know someone who owns a good shop that will give me a good quote, send me a message. Thanks!

Hi, I am looking for an intake manifold throttle body of a 7k EFI KR-42 town ace. I am from Fiji and unfortunately there is no one here in Fiji that has this exact part. I really do need someone to help me with getting this part. The picture attached is currently the intake manifold throttle body of our vehicle that is bugged. would appreciate a help from anyone in this forum right now. thanks

Đà Nẵng hiện nay đang là một điểm du lịch nổi tiếng thu hút lượng lớn du khách. Với nhiều điểm tham quan, giải trí, nghỉ dưỡng Du lich Ha Noi Da Nang 3 ngay 2 dem ắt hẳn sẽ đem lại cho bạn những trải nghiệm tuyệt vời, những giây phút vui chơi thoải mái nhất. Hãy mau xách ba lô lên và đi thôi nào!Phương tiện di chuyển khi du lịch Đà NẵngTừ Hà Nội, bạn có thể đến Đà Nẵng bằng: - Máy bay: có thể săn vé rẻ của các hãng JetStar, Vietnam Airline hay VietJetAir- Tàu hỏa: nhớ mang theo CMND khi mua vé bạn nhé, thời gian di chuyển khoảng 14 đến 20 tiếng, bạn nên đặt vé tối để có thể ngủ một giấc sáng dậy mở mắt ra đã đến Đà Nẵng rồi- Xe khách: có thể tham khảo các hãng xe lớn như …

Hey guys, New member and new to Toyotas. My background is old Ford Escorts and modern VWs and Skodas but want to try something different so looking at getting a KE70 . I'm keen to do a conversion but unsure which way to go, 4age 20V or 3sge beams? From what I've read on your immensely helpful threads the 20V seems like an easier conversion? That extra power from the beams would be nice though. Is the extra power from the beams worth the extra effort or would some cams and head work on a 20V be not far off the beams? Thinking of doing hillclimbs so running in the 1600 class as opposed to the 2000 class would also be advantageous. Also, does anyone on the forum do or know o…

Cowrolla

Good day all. I am new to the club , I have a KE 70 corolla 1.6 GLS sprinter 1982 model and I am looking to buy tail lights, head lights and grill for my car. Does anyone know of places where I can buy new/used parts that are in good condition ? I have attached some pics of my car. Thanks.

Hi team, First time post here so let me know if I’m doing this right.. basically I’m wondering if any members here are able to point me in the right direction for a tuning/carby specialist shop in the Rotorua/BOP area. Might be a long shot but worth a try. I’m currently battling with my 4k build and hit a brick wall with the finer points of fuelling and breathing. Main points of interest on engine are - 1mm bored block/oversize pistons. 3k head with 20 thou skim. Wade 140 cam. Lightened flywheel. My current work schedule and being overseas has meant that I haven’t even touched the car in 3 months or so. And I can’t even remember where I left off, so prett…

Hi All As a proud new KE70 owner I have some work to do ready for an MOT (Fresh Import) - It came from Thailiand and has some yellow film on the front window which is an MOT failure in the UK, any suggestions for removing it it sems to peel of - in small pieces

My rear main seal went in my ke35 coupe for the first time since ive owned it, plan on replacing it asap as of course my daily has died as well just wondering what it would be worth replacing at the same time to avoid future maintainance? Clutch etc? Cheers in advance

Hi Guys n Gals Just got my L's 5 months ago and i decided to buy a ke70 wagon, came with a ca18det witch i can't but in while on my p's because i think it out puts 280kw or something the guy said (probs pulling my leg) But I;m going to take that out and put a p plate legal engine in. I'm not sure what engine I'm aloud to put in it if i can put a 4age or do i have to stay with the factory engine it came with witch was a 4k-c I see that NSW p plate laws have that i can't drive Power to tare mass ratios of greater than 130kW per tonne or, Modified engines that need to be approved by an engineer or, Other vehicles classified…

Hi All id like to hear anyone's thoughts on a 4Y transplant in a ke70. Has anyone done it, mainly as a civil daily driver. Any input greatly appreciated. cheers Max666

hey guys,it's me again,i have a 2K engine in my pickup-KP36,and i really need some help :/ .First of all i m looking for an intake manifold to buy,from europe,only for 2K engines,and about 50-85 euros.Second,i have to know if it worths all my tries until now about putting my cbr 600 carb.I didn't do any mods on the engine inside,i just run on a little more psi fuel pressure from my cbr 600 fuel pressure regulator.Any help will be acceptable,and please tell me how to write my topics on rolla club page only,as i am new here.

Hey guys, I was doing to some research into finding a front lip for my slant nose Ke70 but didn't really like the variety thats on the market. Has anyone done this conversion or is there other alternatives to making a full bumper

Will a 5 or 7K motor bolt to a 4 K trans ? Seems no one here has any idea .

Hi guys Wondering where I can get a hold of an Air conditioner condensor for my KE70. It's got the standard 4kc motor and it's a 5 speed manual sedan. Tony

Normally E-series engines come with C150 transmission, and when engine is upgraded to 'A' series e.g. 4A, 5A, or 7A, the trans is also upgraded to C50 or any C5X now i have an fwd corolla with 2E (12 valve) engine,that already has C40 transmission instead of C150. Just wondering if C40 and C50 are both same with 5th gear difference like k40/K50 or completely different. if C40 can work with 4A or 5A, this will save us some cash. YM

I have a friend down in NSW, up Gosford way, who is in the final stages of finishing off an SR20 Nissan engine rebuild, with all the good stuff, as part of the engine makeover/upgrade. He wants to drop it into a Corolla KE70 body; but is having great difficulty, locating a reasonable KE70 body. He doesn't mind if it is just a shell, as long as it hasn't got extensive rust. Obviously, He won't be put off, if it doesn't have an engine in it, as He has His SR20, just about ready to drop in. Obviously, if it was in the Sydney greater area, that would be ideal; but is prepared to transport it from anywhere, within a days drive ! If You have seen a "reasonable one", at …

Hey guys. I just picked up a 78 TE31 and I'm trying to save it but it will require a few parts. I have searched on here for links to parts but most are dead now. There also are not any listed on a Facebook search. Any idea of where I can get some parts.....both sheet metal and trim pieces? Thanks. PS: I am located in the US but don't mind getting parts from overseas.

Hello all! I'm Jonathan from sunny southern California. Currently working on a 1982 TE72 sedan. Thank you for having me here.

Buen día Tengo un TE72, tengo el interrogante de como se comporta la luz indicadora (cinturones de sujeción) según con el diseño original En mi auto pongo el motor en marcha, la luz se enciende pero pasado unos pocos segundos esta vez se apaga sin importar si los cinturones están o no abrochados Y no sé, si esta luz debería apagarse hasta que los cinturones se abrochen. ¿Podrían ayudarme a despejar la interrogante?

Hi Guys, new to this forum. Thanks for having me. I'm moving from Qld to Syd and will bring across my KE30. Currently on full Qld rego. The car is modified with a 5K motor, K50 gearbox and diff to suit. Everything else standard. It has been engineered in Qld to be registered. However, I will need to do this again in NSW. I would like to register the car under modified historic registration with the club once in NSW. Can anyone tell me what I will need to do to have the car ready for historic rego and estimate of cost involved? Thanks in advance.

Are Ke70 and Ae70 bushes the same the reason I'm asking is i have a Ke70 with Ae71 front end in it (4age conversion) and i want to order all new bushes

Hey, I'm fairly new to the forum picked a KE70 with a 4k a few months ago for a second car have a little fun with you know the gist. Recently its blown head gasket and turned my oil into milky sludge. It's a low K motor on the odometer (but you never know). But i'd like to rebuild it and have her sound a little better its an all original car drives nice with minimal rust, like to give her a fresh motor. Perhaps with an aggressive Cam and head work. Anybody know any engine builders they can suggest for this motor. My plans for the car are to keep it original I don't want to engine swap or be a target for defects, its just a little cruiser to occasion…

Hello . I'm in search of a 22 spline yoke for a T50 manual 1983 Corolla Wagon. Also looking for a complete rebuild kit for the T50 . Any help would be appreciated. Thanks .

Where in the hell am I supposed to put my cellphone while driving? I can't install a mount anywhere. Let me know where your spots to place your phone or install a mount are. The center pocket below the screen is too deep, the cup holders are too low, and adhesive doesn't stick to the leather lining.

Hi Guys, just joined the club and wanted to say hi, not new to Corolla's but it's been a long time - bought a Ke20 brand new back in 1973 (yeah I am that old in body not mind) and raced it for the next few years until I totalled it. Had a pretty hand setup making lots of H.P. great handling and all the rest. That was then. So now I have decided to do it all again - bought a fairly ordinary Ke20 with "good bones" and am starting the resto procress. I already need a front bumper, bonnet, stone tray, urgently so if anyone can help please give me a shout. Yeah the car turned out to be "a bit different" to what I was promised in the add and on the phone and was supposed to com…

Hi I’ve been looking around everywhere for some sort of answer to a question but can’t find anything. I’m looking to weld my ae71’s diff but can’t find anything hinting towards the strength of the axles or anything related. Surely the car is light enough that just driving around won’t snap axles?