Engine Conversions
Toyota Engine conversions - Q & A
1441 topics in this forum
-
got a change my cable clutch to hydraulic... need some good directions and help. i just want to no what to buy and what work will have to be done and plus how much itll cost
-
- 3 replies
- 4.9k views
-
-
the 1.6 out of the ae71 will fit straight into a ke70, yes? just double checking
-
- 6 replies
- 3.3k views
-
-
-
hey I'm doing a 4age conversion into a ke55 and just like to here a lil advice from some people. ive been told its easier to put a ae71 x member in my car but ive also been told it doesnt fit. should i just use my stock x member and make up some new engine mounts, but i also heard if i do that the 4age tends to sit too high... please need some help. and also like to no what people did diff wise and also tailshaft wise. I'm thinking of going hilux diff but guys if youve done a similiar conversion let me no. it would help me out so much. cheers
-
i am in the process of doing the conversion, but i would like to know if it will ever be legal. and if not then how do cars like the grimas corolla and the like do it. opinions welcomed. i am in brisbane queensland.
-
- 6 replies
- 3.8k views
-
-
hey guys if got a 1ggte on its way to my place and i was plannig on rebuilding it getting it acid dipped new seals bearings gaskets you know the usual, bosch 040 fuel pump, bigger fuel lines, 14 psi on stock turbos, 300+280+75mm fmic mounted upsidedown infront of radiator support pannel with short cooler pipes(no lag), AU falcon radiator with twin thermos, exedy heavy duty cluch, EB rear springs, 3" exhuast all the way with just a canon or somthing, r31 front springs,gbox tunnel and firewall mods so i can have 200mm of engine in cabin (i measured) to even the weight up as much as i posible can, shortened tailshaft, custom engine mounts/gbox mounts,4wd hilux lsd diff with …
-
- 23 replies
- 23.6k views
-
-
Well, looks like I'm in a position where I can let another car fall on the wayside. The danger wagon is hitting the track. :jamie: My engine of choice? Most likely a 4G54. 2.6 Astron, from a Mitsubishi Sigma that I'm getting off a mate. 5 speed box to go with it. I've seen 300rwkw plus being pushed out of these motors, so I figure I can build a reliable 200rwkw engine. Planning to run a GT20 with around 0.70A/R. I'll keep this thread open to give everyone a run down as I go through it all.
-
- 39 replies
- 37.3k views
-
-
hey guys, iv got a ae90 corolla hatch, and its a 1.4 carbie, 5 speed manual. this is my third car and compared to my mazda mx6 i had, its like a turtle. i am interested in changing the engine to a 4age and eventually putting in a turbo or supercharger on top of that. i don't have great knowledge of toyotas so i was wandering if u guys could help me out. iv got a few questions. 1 how much roughly would a good condition 4age cos from the wreckers? 2 do i need to change the gearbox? 3 do i need to change the ecu, if so which one is best and how much? 4 do i need to change any engine brackets when putting in the 4age? 5 is there anything else i need to chnge? tha…
-
- 7 replies
- 4.2k views
-
-
Hey guys, if anyone knows much about either of these engines or whats involved in putting one in an ae82 then could they contact me via email or msn at [email protected]. Please no 4age or boat anchor comments etc. although having said that I'm sure some smartarse will now. ;) Cheers 200Boy.
-
- 9 replies
- 26.3k views
-
-
WANTING TO DO THIS ONE FOR AWHILE BUT JUST WANTING TO NO IF THERE IS ANY INTERNAL WORK NEED DOING B4 I SUPERCHARGE A CA18DE? IVE HEARD ALOT OF people TURBOCHARGING THERE RB20DE OR THERE RB25DE WITHOUT DOING ANY INTERNAL WORK SO LET US KNOW IF YOU HAVE A CLUE. CHEERS
-
- 3 replies
- 14.9k views
-
-
Hey Guys, i have recently acquired a 2T and am wanting to fit it into my KE20. I only have the engine. No g/box OR flywheel. If anyone can throw me some ideas/previous experiences about this conversion they would be greatly appreciated. :) I'm trying to keep to a minimal budget so the missus can't stop it happening :) . So any bolt in info will make life easier and more fun at the next cruise. hahaha :y:
-
- 19 replies
- 16.6k views
-
-
hi all i know i'm not the most liked person on this website but i do have a person of being here well anyway this is my car it is a ke55 and i have put a 3tc in it and twin 45mm Webbers on it. i also have put a set of 4-1 extractors on it. it has been painted in a blue purple color with a pink and blue Peal i am also putting a silver flack though it. i have put a 2,1/2 in exhaust in it. i have a pair of bucket seats of it and i'm putting all new interior in it tinted windows soon as i get the money to buy them. well hear are some pic's
-
- 17 replies
- 14k views
-
-
Hey, just wondering what you guys think of a supercharged 4KC in my KE20. I will be totally rebuilding a 4K soon with full internals, should be a pretty stout engine. But I have had an idea of bolting on a supercharger from an SW20 MR2 as well. What mods would be needed to get the supercharger mounted and how would I go about setting it up etc. I've heard that if you get a 4K with air conditioning you ditch the air con and mount the charger where the air con was. Any help and/or opinions appreciated. Ben.
-
- 10 replies
- 14.5k views
-
-
i just got a very tidy ke70 with a 3k engine and a stuffed auto box. ive found aTE72 T18 SE with a 3T engine and a 5 speed that is full of rust but it is mechanically very good. i don't know much about the TE72 and i was wondering if the engine, gear box, tail shaft, and diff will bolt straight into the ke70. cheers
-
- 11 replies
- 26.7k views
-
-
-
http://www.onthenet.com.au/~paulp/corolla/ diagram is the 5 links down the very bottom under 'tech bits', says 'main computer 1-4' and 'knock sensor' hope this helps anyone who needs it!
-
- 4 replies
- 17.6k views
-
-
i just picked myself up a 1986 AE82 CS corolla hatchie and I'm researching about a engine for it, the one in there has a bit of zip however i bet my mate i could beat his magna which pushes out 170kw, so its on :) ive looked at the 4AGZE with its supercharger and i was wondering how hard it would be to get one in there. or better yet is there a faster one to chuck in? any help is appreciated.
-
- 9 replies
- 5.1k views
-
-
doing a 4age conversion into a ke55.. need to no how i can make a tailshaft that will fit my diff and the t5o box. really stuck please need some advice. cheers
-
- 9 replies
- 3.4k views
-
-
has anyone heard of an ae71 with like a 7mge, 1jz or 2jz in it , i know it would be near impossible to do and make the car handle but was just wanting to see/hear anything about this type of conversion thanks :n:
-
- 13 replies
- 8.9k views
-
-
hey all... onto yet another good idea for ae71... 4age carb'd... idea was to have a gze bottom end for strength and reliability and then 20v head with quad motorbike carbs and trumpets... havent done much research into it so any information or opinions on the idea would be great... :)
-
- 44 replies
- 95.8k views
-
-
1st off this isnt an easy job, requires a fair bit of cutting and fabricating, if u are thinking of doing this too a neat ke1X forget about it, use another engine. 2nd this is based on a 12a engine as its smaller than a 13b. i have seen 2 different ways of doing thins convo due to the position of the eccentric shaft in the engine (in the middle of the motor, as opposed to a crankshaft sitting at the bottom of the motor) you really want to position the motor/gearbox as flat as possible. too much angle and u get vibrations and snap front uni joints quite quickly. taking this into account the 2 methods i have seen are:- 1.) position the motor as far forwards as you…
-
- 5 replies
- 6.4k views
-
-
just recently received the shell scott sold, CHEERS heaps scotty. i would like to know if it has been done already (hopefully not). how'd you go?? if there were any major proplems ie. structrual, firwall and tunnel work it would be good to know aswell. i made a template of the gear box to suss how i would go housing it and theres some cutting to be done. what would be easier replacing the stock tunnel with a 180 or silvia one. or just making one myself from sheet metal. Help would be much appriciated cheers James
-
- 2 replies
- 2.1k views
-
-
Hi all, I know this is probably the last place i should be asking this, but i thought what the hell, a few of you have done SR20s into KEXX rollas before so no harm in asking. I was putting an S13 SR20DET motor and box into my KE55 but the supplier decided to tell me today that they had sold my conversion package on me, but was given an alternative proposition for not much more money. An S15 SR20DET conversion package :P Now my question is, how different are the intake plenums? I have a commodore style brake master cylinder and am worried that the motor will not fit properly in the bay. I am very keen on this motor but don't want to get it to find out that I ca…
-
- 6 replies
- 4.2k views
-
-
Hey guys i have just picked up my project ke1* and i have been thinking about what i am going to use to power the little thing.. and i started thinking rotary engines.. anybody know much about the conversions and are there any websites i could look at which may have some information on the conversion process.. i have been thinging about ported 12a and 13b carby motors.. any help would be great Cheers Matt
-
- 16 replies
- 6.8k views
-
-
-
someone asked me today and now i wanna know the answer myself.... the question is... is it a loop hole if i engineer it and another state and bring it back to new south wales..? how does it all work..? sorry for the noobness of it all....
-
- 11 replies
- 5.6k views
-
-
hey just wondering if anybody on the gold coast has a engine crane that they could lend me for a few days cheers
-
i got a ke55 and i bought a 4age... just wondering would i need to use a ae71 pedal box or a ke55 pedal box?
-
every one keeps asking about mounts to stuff the 4age into the ke's, if i built mounts to sit a 4a onto ke eng mounts so that they fit everything from a ke10 to a ke70 would they sell/do you want to buy them? I'm even thinking of selling them engineered but thats going to be a pain depending on what state you live in o'yea, how much do you want to pay?
-
- 91 replies
- 71.4k views
-
-
hey all, i have an ae92 imported 100kw (7rib block) 4age in my ae71 and am wanting to make it a 4agze. just seeing if this might be cheaper than doing another conversion to the 4agze and what could be involved....what i am wondering is 1. would i be able to bolt the sc12 supercharger onto the engine and just replace the stock 4age ecu with an ae92 4agze ecu? (will the same wiring loom be able to be used again from the stock 4age)?? 2. would i need to rebuild the engine with 4agze internals or would i be able to just leave the stock internals???? I'm sure there would be some other things involved so if anyone has any info that would be found useful please feel fr…
-
- 10 replies
- 11.9k views
-
-
I'm a noob so I'm sorry if this has all been done before. i've looked through all the engine conversions threads and still didn find the answers I'm looking for, then searched some more. so my situation is this. i really want a 69 rolla as a daily, i will want to upgrade the engine to either a 4k with all the stuff to give it a bit of get-up (which i kno is straight forwardish) or a stock 4age (seems to be much more complicated to get in but with obvious advantages of no performance mods, newer engine etc) also i need a car to keep me going which is why whole cars instead of just engines, the conversion wouldnt be done straight away my plans to do this are: buy a r…
-
- 4 replies
- 2.7k views
-
-
hey guys, jus wondering if anyone knows someone that has done this conversion. I'm thinkn bout put 1 in a ke70 track car. jus wondering how difficult it would be and it would need many custom parts etc.. any help will be much appreciated. cheers Jack
-
- 21 replies
- 9.9k views
-
-
Hi all I'll start by introducing myself my name is Jarrod I live just south of Brisbane and have a 78 ke30. My question, I have looked through the faq's and read the 4age into ke70 and was wondering will I be able to use the ae71 crossmember in my car for the 4age or will I need a different one. Any info would be great as i am new to the old school rolla sceen. Thanks Jarrod
-
- 7 replies
- 5.2k views
-
-
i hav a ke25 4k at the mo bt wnt 2 put 4age 20v, need sum help,
-
- 10 replies
- 16.5k views
-
-
Hey guys I'm having a bit of a problem gettin spark out of the coil, i was wondering if anyone had any wiring diagrams or could explain it to me, thanks for any help
-
- 4 replies
- 10.5k views
-
-
hi there all, I have got a 4agze and am looking to put this into my ke20. I am wanting to know if anyone can help me with a couple of things.... 1- What model engine mounts will i need to make it fit into the K frame. 2- I want to put discs on the back so what sort of diff will handle the engine and have discs... 3- I was looking at a T50 gearbox to mount into the car, will it mount directly to the engine and car frame... Sorry to ask so much but thought i would ask anyway....
-
- 13 replies
- 15.2k views
-
-
Hi guys this is the run-down of where I'm at at the moment What I have: Early model silver top 20 valve 4A-GE engine, gearbox, ecu. SC12 supercharger (I'm unsure which pulley size it has on it) This is what I'm thinking of getting/doing: Head work: Port match manifolds Mild port and clean up of head, remove any hotspots etc. 1JZ 380cc? injectors Bottom end: Arias 9.0:1 oversize forged and ceramic coated 20v pistons (has valve cut-outs) Shot-peened 20v rods ARP bolts for EVERYTHING! Theres other stuff I can't remember at the moment but anyways... I only plan to run around 8-9psi max. The main aim of this project is to build an engi…
-
- 37 replies
- 14k views
-
-
hello i have a dirty shitter of a ke70 wagon that i use for a daily. would really like to put something a tad bit bigger in than the 4kc. someone i know has an engine out of a t18 but i'm not sure if it will bolt straight up. not interested in anything efi. on an extremely tight budget (might be able to get this engine for $50). i have searched but it seems anyone doing a conversion is doing a worthwhile one. this isn't my project car, just want it to be able to overtake occasionally and not be such a slug. cheers
-
- 25 replies
- 6.9k views
-
-
-
hey i just did a engine swap in my ae82 it had the standard 86kw tvis 4age bigprt, and i have a put the 100kw small port in it. got it all going but it keeps cutting of when u pull up at trafffic lights or stop sudenly.... has any1 had this problem before? i have taken it to a efi auto electrition and he reakons hes never seen anything like it. could it be ive used the 100kw injectors and they flow alot more than the 86kw ones as i did a flow test, could these bigger injectors be puting to much fuel in and the computer can't handle it or..... any help would be realy appreciated cheers nick
-
- 4 replies
- 3.5k views
-