Car Electrical
Car electrical gremlins/questions? Ask for help here..
959 topics in this forum
-
my voltage regulator flipped out,charge light would stay on and i could hear it ticking when the charge light flicked off and on.i got a new one,but same prob.please help.
-
- 5 replies
- 4.3k views
-
-
I came across a problem with wiring of my ke 55 I re wired my alternator wiring and now the car gets absolute no power at all no lights nothing all that happeneds is that a green and yellow wires that are connected to the positive terminal just start smoking???
-
- 0 replies
- 2.6k views
-
-
We need someone who can help us wire our Ke70, with 4AGE 20V BT, running on COP setup. Plus other electrical stuff needs to be wired as well. Pm us if your interested, and we're in Adelaide
-
- 0 replies
- 2.9k views
-
-
Hi Can someone please help me out regarding my current project 4AGE bluetop bigport into my Zook. Any help appreciated. Question is there is a black plug in the photo both pins have ignition power one wire is yellow and the other is black and red. What are they for and also what plugs into? As i do not have the car harness only the engine loom as it is going into my zook. Also i got the igniter from a wreckers it is out of a later model corrolla is this able to be used on this engine? I have attached a phhoto of the ecu to see if compatable with that igniter. Cheers.
-
- 0 replies
- 2.4k views
-
-
hey every 1 i need some help ive put in a blacktop ecu and loom into my silvertop also put the map sensor in its running but really rich and idles like a rota lol any ideas ive herd its been done before?
-
- 1 reply
- 5.2k views
-
-
Hi all friend, Firstly i am adree from Malaysia. and sorry if my writting is so bad. I use 4agze in my KE70, so i plan to make charger light inside original meter KE70. Can anyone tell how to find wiring charger light where is it. Is not my mistake, in ECU have supercharger port but not sure is for light or for charger switch Thanks all
-
- 1 reply
- 4.3k views
-
-
Hello guys my project are almost done...know my problem is no spark on plug...was connect from coil to dizzy...( which wired for power on ecu? and more I'm noobies see the diagram engine is 4age redtop...I'm alone work this project.....urm also no signal (battery) on my Tacho..pls help me step by step :( thax rollaclub
-
- 3 replies
- 4.2k views
-
-
Hey guys I'm having some trouble hooking up soom driving lights to my ke55, i need to know how to do so through a relay???? Any help would be greatfull :) See ya Jimi
-
- 5 replies
- 14.3k views
-
-
Hey I'm chasing a 4k-e efi wiring loom, or someone to make me a loom. Any ideas or suggestions
-
- 10 replies
- 13.8k views
-
-
Hi guys. I have an '84 KE70 (no tacho standard) and I bought a "DRiFT" 3" tacho just to jam in there so while I'm burning around in my 40kw I can watch the pretty coloured needle move up and down :) My dad and I wired it up ourselves as per the instructions; Red wire to 12V ignition, Black wire to a good earth, Green wire to negative side of the coil, and White wire to dash lighting. The lights all work fine, the power works fine (turns on with ignition only), but I'm pretty sure the tacho reading is wrong, and the needle also jumps literally 500rpm up or down in any given spot, it just flickers around. We've tried wiring the RPM signal wire to the dizzy instead of th…
-
- 2 replies
- 5.2k views
-
-
Hi all. "Sold" my AE82 twin cam to a "mate" who was supposed to pay me off but after having it for four months until it ran out of rego, then conveniently dropping it off at my house while i was at sea and doin a runner... Anyway,, apart from destroying the interior i found he had cut the wire to the alarm and now the thing wont start... I got reds but it wont crank and the hazards and all sorts of shit starts to flash and carry on. I have tried rewiring the alarm but still no good.. Put a new battery in and the same result. Any ideas?? Cheers
-
- 3 replies
- 4.1k views
-
-
I have just finish replacing my timing belt waterpump and all that mumbojumbo, all went good till i jumped in to take it for a drive and the radio now doesnt work nor the clock i have checked the fuses that i know about and there all fine, does anyone know about this problem and anyone have a diagram of the fuse box and what fuse it is?
-
- 4 replies
- 4.1k views
-
-
Well there guys I have fitted a 4age to my KP60 starlet (not a corolla I know!). I will throw a thread up shortly if I'm welcome? Reasonably standard but CBR 900 bike carbs. I was running a 4k dizzy in it with an adapter I made until my exhaust cam cracked more than likely as a result. I am rebuolding the engine and don't want to chance it again. Looking for a good cheap alternative. I was on to a crowd in England, H and H ignition solutions (I am living in Ireland) but you're still looking at €300-350 for a standard 4 age one converted to electronic with its own advanced curve. I know I can run a locked dizzy and a box like MSD or Jaycar but would like more info. maybe? …
-
-
- 17 replies
- 108.9k views
-
-
hi i have been bizzy with my ae71,I'm stuck on one thing i wood like to know whot wire i need to tap into behinde the dash for the alternator charge light to work?? i wood like to keep the stock light in the dash working,can anoyone pin point me whot wire i need under the bonet even????? any help wood be nice!i have most the wiring sorted just wood like to know this thanks.
-
- 1 reply
- 4.1k views
-
-
first off you need a vl 80amp alternator witch looks like this make sure you get the loom connector that plugs into the regulator! also grab a couple of regulators just in-case the ones in your vl alternator are worn! step 1 - dismantle the 4k alternator and vl alternators. step 2 - swap all the internals from the vl alternator to the corolla casing and use the vl fan (more fins = better cooling) step 3 - now remember those 4 LONG bolts holding the casing together? you need to find 2 about 2cm longer (i got mine from a 5k starter motor) step 4 - install those 2 longer bolts with the rear bracket and bolt it all up step 5 - install the regulator…
-
-
- 62 replies
- 127.9k views
- 1 follower
-
-
Hey guys ive got a ca18det in my ke70 and ive rewired it after am electrical fire the ecu turns on fine but as i start cranking it over the ecu shuts down ive replaced ecu, ignitor module, batery, cam angle sencor and all burnt out wires and the car still wont start any ideas?
-
- 0 replies
- 1.7k views
-
-
Hey guys ive got a ca18det in my ke70 and ive rewired it after am electrical fire the ecu turns on fine but as i start cranking it over the ecu shuts down ive replaced ecu, ignitor module, batery, cam angle sencor and all burnt out wires and the car still wont start any ideas?
-
- 0 replies
- 2.4k views
-
-
yo rollaforum few questions regarding my missfiring k motor today i noticed i have a crack and some calcium build up inside my dissy cap, from my knowledge, this not good, shoudl i just replace these or is replacing the whole ignition system, i dotn want to modify it or anything i just wanna replace it all, but I'm insure of where to get the exact parts from, are there any part codes or something i can repco that shit up cheers
-
- 4 replies
- 4.3k views
-
-
i just tried to start my ke35 i wrecked,it wont crank,its making relay noises at the relay under the dash. ive removed the instrument cluster,and it started fine before i removed it. does it need to be mounted to start? i really didnt think it would have been necessary for it start. if it is can i bridge the plug to start it.doing my head in here
-
- 2 replies
- 3.1k views
-
-
I'm new to this forum, well any forum, but I am in dire need of help! I have just converted my "84 KE70 too an AE82 Bluetop (Bigport) 4AGE engine, and I am having some problems. The car runs fine and is perfectly driveable up until about 6000RPM. It confuses me because it runs so well up until this point, but as soon as it hits between 5500 RPM - 6000 RPM, the engine, runs out of spark? I suppose, and spits and backfires and carries on and will not rev any higher. Also with a timing light, the timing is sitting at about 15 degrees advanced now (with the distributor retarded as much as I can) and does not retard anymore, only advances to about 45 degrees advanced) and …
-
- 3 replies
- 24k views
-
-
Bought a panelvan the other weekend And I am just trying to suss out a few things that are annoying ... So the first electrical gremlin is the cluster lights. I have checked both fuse boxes on the drives side. The ones inside the cabin and they are all good.... I haven't looked any further than that. But every other light works bar the interior light which the fuse was blown.... Cheers mates!
-
- 6 replies
- 6.1k views
-
-
G'day, I have a 1984 Ke70 corolla with a 4KC and auto. I just put a new battery in it recently (good quality one) and it would be flat after a few days (even when driving it often). I initially thought alternator but thought if it wasn't charging then the charge light would be coming on? I don't have a multimetre unfortunetely. I have one of those jump packs and it was getting me out of trouble the last week but now even when thats hooked up it just struggles to wind over. But then i let it sit for a few minutes and it starts off the jump pack brilliantly. As i drive it the wipers are very slow and the stereo cuts out. I'm leaning towards a voltage dro…
-
-
- 4 replies
- 5.2k views
-
-
Hi Guys I'm hoping you can help me. I have a Corolla Conquest 2007 and the lights have started to fail. The Dash lights and park lights are not coming on. for about 2 days they would take about 30 seconds to turn on but now nothing. I have tried looking for the problem but I cannot see any obvious problem. Doe anyone know where I can find a Diagram of all the wiring so I can start testing with a multimeter? Cheers Edward
-
- 8 replies
- 5.9k views
-
-
Anyone near busselton able to lend a helping hand and help me wire up my 4age? Pm if so thanks. Sorry if this is in the wrong section.
-
- 5 replies
- 3.4k views
-
-
Hey guys need help identifying some loom plugs. I can't take/post pics at the moment as I'm on my mobile. The loom is, for lack off better knowledge uncut... For a 16v bluetop. Firstly, I have 4 plugs near the ecu, 2 yellow 1 white and 1 black. 1 yellow is a 14 pin plug. The other yellow is an 8 pin plug. The white one is 2 pin with just a white and black wire. The black one is a 10 pin one. Near the wiper motor plug I have 2 more plugs, a black 2 pin and a white 4 pin. I have a white 2 pin plug near the positive battery terminal. Looks like a giant round plug? Also near that is a single pin yellow plug. Near the a/c green plug I have a blue plug with ligh…
-
-
- 18 replies
- 83.7k views
-
-
Hi guys, New to owning a Corolla. Love it. I have a AUS 09/2006 Ascent Seca ZZE122R and I need to replace the 15v Cig lighter/radio fuse (assume they are the same one) and I cannot... for the life of me find the fusebox under the steering wheel. I am aware there are two fuseboxes and the one I require is the fusebox which contains the radio/cig which as far as my research tells me is under the drivers side around the steering wheel. I have followed instructions online and it seems people have hilariously different ideas of it's location -Right kick panel -To the left of the steering column -Left kick panel -Sort of to the middle right near the steering colu…
-
- 1 reply
- 21.2k views
-
-
I was driving my ke70 when suddenly everything stopped working i have my driving lights workig and the car kept running but all wipers blanks and dash lights are all out, the only dash light on is the charge battery light
-
- 2 replies
- 3k views
-
-
Hi guys, in my ke30 fuse box the 15A fuse labelled "engine" keeps blowing, and my charge light is staying on, is there something related between the two ? and what does the "engine" fuse connect to? cheers all!
-
-
- 13 replies
- 47.3k views
-
-
Hey all, (I really do not know where to post this) My little old bomb is starting to add up in price and I have been thinking of some type of alarm system for it before it goes out into the big bad world. I had a search but nothing came up for a “GPS tracker/ car alarm and I was just wondering some of the pros and cons of some of the brands out there on the market. I have not done any research into this myself yet but I’d like to hear from what you have experienced or heard . I have been told that some of the more upper market alarm systems have a sim card in them and they will text you if the current state of the car is changed. Thanks for your feedback.
-
-
- 9 replies
- 8k views
-
-
gday i have a liteace with a 4kc engine. it is fitted with a dual battery syspem but the standard alt can't keep up with it. are there any other alternators that have a higher ampage that will go in easy?
-
-
- 1 reply
- 10.9k views
-
-
Hey everybody, i've been stalking for ages, but never signed up so i didn't ask a billion stupid questions, search has been able to solve most things, but now I'm stuck. I have a KE70 sedan with a 4k and auto. If i have the stick in park it says park, and if i change it to any of the other settings drive/reverse/nutral it still stays on. i wondered if the switch in it is buggered in the box because when i go from park to reverse it flickers a bit. I'm not sure if this is a common question or not, but would love an answer. cheers :D
-
- 12 replies
- 4.5k views
-
-
Hey guys. Sorry to ask this as normally I'd try diagnose it myself, but I'm at work and the shops are closed tomorrow so I'm trying to see if I can get an answer so I can get parts today when i do deliveries. Just rerplaced my plugs and points. (4AGE bigport) My issue: Seems fine accelerating, when cruising at low throttle its jerking and coughing a bit. Plus backfires and stalls. I'm pretty confident I have the right leads. I put NGK BCPR6 (or 5 I'm not sure)EY-11 plugs in pretty sure the 6/5 number shouldnt affect it but did I get the correct plug gap? There were two listings for 4AGE a 0.8 and a 1.1 gap. Or could it be that they are the Y and not the P plu…
-
- 8 replies
- 13.3k views
-
-
Hey all, As title states, required is a KE30 3K Engine Wiring Diagram for the "Joely-Rolla". The wiring is there, but we don't think it's wired correctly. After throwing in a working battery, it cranks, but won't fire. We reckon it might have something to do with the Coil side of things. If someone has a photo, book, diagram, or knowledge of one, please let us know by either posting/sharing the photo, or section of a book of it. :) It might not be much help, but below is a photo of the engine bay with the coil and wiring in it. Cheers, Woz, Josh & Joel. :cool:
-
-
- 8 replies
- 41.2k views
-
-
Hi all, I've been away from rollaclub for a while, at the moment I am building an AE71 with JDM bigport and JDM fuel tank. I am stuck with too much confusing information regarding the wiring. I have a circuit opening relay. I have one of these http://www.jaycar.com.au/productView.asp?ID=SY4076&CATID=79&form=CAT2&SUBCATID=979#1 And i need to know how to make it all work Ive grounded the earth wire from the fuel pump in the boot I also came across this: White/Black - Wires to to STA - Starter/ECU Start Signal. White/Red - Wires to EFI Relay - +12v Ignition Switched power (Run through a suitably sized fuse, 10A is us…
-
- 29 replies
- 267k views
-
-
I bought a 12v 10watt LED light off ebay. Plugged it in and it came on and lit up the shed then burnt out i guess. I msged the seller and told them what happened and they said the light only requires 2 amps other wise it 'll burn out. Well they didnt tell me this so they have sent me another for free. What do i need to do so i don't burn the next one out ?
-
-
- 21 replies
- 48.9k views
-
-
So I'm putting one in so I get a more accutare temp reading. Google has been all over the place on this one. The last one I put in was mechanical and this is electrical. Q: Can I hook the new one up to the stock 4age signal wire which is also running the dash gauge or does it need its own signal source? (I have a rad hose sender mount). Would running two off one signal source result in inacurate readings on one or both gauges? Q2: Does it need to be grounded to the engine, or just a good solid ground? I have read a few different opinions on this, some are adamant to use and engine ground, some say just a good solid ground on the chassis. Cheers guys. Reed
-
- 4 replies
- 3.6k views
-
-
We were helping a new twincam owner today to do his timing. He shorted out the wrong wires on the service plug (see pic below) and now the check engine light does not come on and the engine cranks but wont start. We checked all the fuses but still nothing. Anyone got any ideas? Thanks.
-
- 8 replies
- 6.9k views
-
-
i installed a tacho in my ke 35.. its 52mm cheapy where the clock normally goes, its got settings on the back for 4,6,8 cylinder.... its all wired correctly and is set on 4 but appears to be reading double.......idle showing 2,000 rpm and as revs build goes all the way to 7,500rpm to easy.. don't think the 3k will see those revs lmao.... the tach signal ive taken from the - on the coil... been told need to put a resistor on the wire..is so how many ohms?? before i put the resistor on what will happen if i set the tacho at 6 or 8 will that potentially fix the issue? :jamie:
-
- 15 replies
- 35.9k views
-
-
Hi I have a original ke20 rev tacho and I can't get it wired up can anyone assist me on this? It's got a red, green blue orange brown and another red wire. I connected the red to power and ended up being earth. Spinning me out!
-
- 1 reply
- 3.9k views
-
-
G'day. The wiring in my ke10 under the dash in my ke10 could do with tidying up and i want to put a new radio in it. It has the late model Ke11 dash in it. Does anyone have a wiring diagram or can tell me what colour wires do what? Cheers
-
- 11 replies
- 15.5k views
-