General Mechanical

will ae71 frnt suspension fit ke55

G'day i have recently bought a ke55 rolling shell that had a 4ahe in it, it apeares they have moddified the crossmember to suit stock 4age engine mounts, i was just wondering if any one knows if a 3t will bolt straight in with t18 engine mounts? also is a t18 clutch master cylinder to short for a ke55? i had to extend the small pit that protrudes of the rod, we can't get the clutch pedal to get pressure, any help would be awesome thanks, casey

I was changing the brake pads on the 30 today and broke a locating wire inside the caliper, so off to the wreckers i go. the guy said ther was a ke30 out in the yard so off i went. Went to get the part i needed....DIFFERENT!. I know this is very ignorant of me as i can recall reading several threads on how they were different but i simply never took any notice. Now, as i have a ke10 that needs disc brakes i will put the ke30 ones on it, but are the 55 ones a direct bolt in affair for a ke30?. they look like they are, the only thing that may be different is the brake hoses. Any help would be appreciated. (p.s. sorry to ramble on :P )

With the power upgrades occuring to the corona, something has to be done about the suspension, which was to say rubbish. Since I don't have a front subframe at the moment I started with the rear suspension. To my pleasent suprise RT40 coronas have 5 rear leaves (corolla's only have 4,) thus the the decision was quickley made to invert and clamp the bottom 3 leaves on top. This has the effect of flattening out the leaf stack (lowring the car) and making the stack much, much stiffer. Results are as follows: vs the new: Installed the difference is obvious, it also became apparent that the diff has now moved backwards 2cm or so. I'm yet to finish the seco…

ive got a ke20 corolla and i found some rims i liked but there on the internet so i want to be sure they will fit they are the right stud pattern but i wasnt sure about the offset. they are 13 x 5.5, 4 x 100 PCD with 46p offset and a 56.1 mm bore hole. thanks rollas . peace

I'm chucking a 4AGE on carbies (because carbie are Sik :wink: and sound awsome :hmm: ) into a rather clean RT40 corona. Mounts are sorted, carbie linkages are sorted, exhaust is sorted, cooling is sorted, fuel is sorted, clutch is sorted (RT40's have hydro clutch from the factory :y: ) However ignition isn't sorted. I've heard rumors that you can use a 4AC dizzy, with a sleeve and all's good? is this possible, do you need anything else, an ignightor for example. Has anybody got ignition kits for carbie engines? Others have suggested a Sigma Dizzy? is anything else required? need asleeve or mounting plate? the only other thread I found was back in Feb ad didn't re…

any bright ideas? The front oil seal is spewing oil at an alarming rate and needs to be replaced. Standing between me and DIY progress is the crankshaft timing pulley - which I can not pursuade to seperate from the crank. hellllp!! Slapper

Hi, Just yesterday I got a full fairly new exhaust system for my KE15. All the system fits APART from the exhaust mani that bolts to the head. After stripping it back today to bare metal and painting it I noticed the heat exchanger box on the KE10 mani has the 2 bolts towards the cylinder head and the single bolt towards the wheel side of the car. And this manifold is off AE70's KE10 so it is an original manifold. So did some early KE1X manifolds have the heat exchanger box bolt pattern backwards? As Most normal corolla K exhaust manifolds have the single bolt on the cyclinder head side and the 2 other bolts on the wheel side. So in effect the bolt pattern is …

Well, last night I ran out of fuel about 100metres away from a mates place, so I went to see him to see if he had any spare jerry cans of fuel laying around. Anyway, he gave me a little can and said that it was regular unleaded. Under the assumption that it was, I put about 3 litres of it into the tank which was all i needed to get to the servo. Unfortunatley I realised as soon as the car started that it wasnt just regular unleaded, so I said to him "You sure this is Unleaded?" to which he replied, "Oh wait, I think that is the 2stroke premix for the wipper-snipper...." :y: . I managed to get to the servo where I put about 10L of unleaded into the car, hoping that it woul…

as the topic says, i got told you can jsut 'shorten the diff tube' but I'm not sure whats meant by that. or do i have to go about cutting down axles and things as i assumed you would. can anyone break it down for me please? thank you.

hey guys i have a 1989 model toyota corolla seca AE82 liftback . i was givin the option of using my money to put rims or lower it with king springs on super lows dropping it 50 mm and putting a strut bar . so it will make the ride more more responsive and tight in turning. i have bought my suspesion and instailed it . however i don't know whether i should buy a after market strut bar or weather to get one from a rolla that would fit my one. does any one know if any models of the rolla came with the strut bar or would i have to buy a aftermarket one? thank you niran

Hey guys, would anyone know the offset of the gen10 rolla? i'll be calling up toyota in the morning, but doubting they'd know.. I'm looking to get some wheels, but want to make sure the offset is right, would +50 offset be too high?!?!

Hello. Just curious as to any radiators people have used to replace and upgrade the standard item in their AE71/KE70 4age project. Ill need one before the heat of summer kicks in. I'm looking for something about 410mm high, by 550mm wide, with both hose connections on the drivers side. So far my best option is looking like a rebuild of a standard one, to include 3 cores. This costs in the vacinity of 500 dollars, so Id rather find something potentially better and cheaper. I don't mind fabricating any mounts to make it fit. don't be shy now.

Hi all, i was just wondering if early ke30 disc brakes will fit under 12" rims? My ke20 has to look standard but ke30 parts are easier to get. Any help appreciated. Thanks

Like the title says, it only happens at around 60km/hr then dissappears. It is probably the worst vibration I have ever seen. I put a different set of wheels off my ke10 on and that had no effect (they wheels off the ke10 may not be balanced) I guess i really should spend some money and get the wheels balanced first. But say its not the wheels, where do I start? Is there a common problem that will save me hours of time (& money) wasting? (probably not because search turned up nothing) I was planning on replacing the hub bearings and checking the callipers. I have had a good look under the car and can't see or feel anything loose in the steering. The fact that …

hey guys, i've fitted my 3/8 bundy fuel lines no dramas, what my question is should i the inlet and outlet fittings on the fuel tank be made bigger or will be it be ok to leave as they are as they are going to my surge tank first and then from the surge the larger 3/8 fuel lines get connected. cheers thanks in advance

hey guys, any clues if the front struts from a ke55 would go into a ke11. i'm doing a eng conversion and will need front discs to have any hope in stopping. has it been done and what would need modify cheers james

Gday all, I've got two rooted KE70 seats that have had their share of broken-ness for quite a while. That, and I hardly fit in the damn car. What seats and rails would allow me to sit further back, lower, and would keep me in the seat apart from a racing seat (not ready for that yet)? it's a budgo job, so anything too expensive will not be considered - period. start throwing money at unnecessary stuff, the fun goes away pretty quick now doesn't it? Thanks guys.

Gday all, I have a 1999 AE112 Hatch that's central locking appears possessed. Driving after about 10 minutes the locks try and unlock themselves. Is this a common occurence? After you've stopped, locked the doors and walked away, they open by themselves also. Any help would be greatly appreciated.

i was wondering if the ke30 2 door, door window is the same as the ke3x panel vans??? I'm getting sick of my lexon window, due to can open it... and the race car gets bloody hot inside...

Where specifically is it located? I'm not finding it.

could someone identify this 5 speed box for me please i think it's from an early corolla, has a 20 spline shaft, also i need a yoke to fit drive shaft. any help would be appeciated there is a number stamped on the side of the box 33111-10031 2 cheers IS IT A K50 I hope this is in the right section??????

any info on inlet mainifolds have a 5k head -what would be better for max perfromace 3km inlet/4k or the 5k cale12

need some push rods asap ! just got a cam in but the push rods are to long and the supplier has none in stock please reply with numbers and cost if possible cale12

hay guys ... just doing a little research into lowering my rolla.. the rear shocks are gone so was going to upgrade them when replacing but was wondering if i am going to lower the rear will i need shorter shocks... also what shocks do you guys recomend ... is it a hard process to do myself swapping shocks and lowering the car all round... oh and also what set up at the front do you guys also recomend keeping in mind i want to do it properly not dodgy like cutting the springs etc...

as i posted somewhere else but thought i should start a new thread, so someone care to eleborate please..? am i right or wrong..? I'm curious for both front and rear, i have coilovers made from a commodore strut (so i can always use a bigger shock if needed) bilstein adjustables and a king coilover spring, are the coilovers being let down cause I'm not brand whoring and going cheap on the spring.. or is a spring jsut a spring? any info would be great thanks.

Hey guys, My dad and I recently installed a 32/36 DGAV Weber on the 4K as the old Aisan one that was on there had basically lost it's will to live. The carbie is working pretty damn nicely however we just encountered little problem and are unsure what is causing it. The problem is that after the car has been driven around for a while(5minutes or more)then turned off, it doesnt like to start up again straight away. (noticed when trying to start the car after stopping at the petrol station :yes: ) You kinda have to let it sit a bit then try again. Once it finally starts, it gurgles for abit at about 300rpm then slowly rises to a normal idle(1000rpm). It seems as if…

Hi, As the title says I found out last night reading my KE1X aircon manual. If the KE1X car was fitted with factory aircon they also installed a factory electric fuel pump in the boot. So for some reason on the KE1X with aircon they ditched the diaphragm pump and used an electric one in the boot. Below is 2 scans of the manual showing the fuel pump exploded view and the number and part list page showing how the number matches up from the exploded view to fuel pump. Also notice above on the fuel pump exploded view page the image outline of the motor showing how the fuel line goes to a bracket and on that there is a regulator mounted and then it goes to the…

hey does anyone no where i can get extactors made up for a rwd 4age on the goldcoast? or maybe where i can buy some cheers

hi does anyone know of an exhaust manifold ( not extractors) for a 4kc motor that has twin outlets, the ke70 i have has a cast iron exhaust manifold that has a single pipe outlet, i would like a twin outlet. the motor and 5 speed gearbox slightly warmed is going into a Honda S600 roadster, also using the corolla rearend but narrowed, i'm using twin 1.5 inch su carbys. i don't want to run extractors unless there is no other option, if i could get a twin outlet cast iron manifold that would hopfully free it up enough. any thoughts?????? regards Ewen

hey guys i am looking to replace all the window and door seals on my ke1* project which i have recently started as it is leaking water chronically into the car .. my problem is that clark rubber can pretty much supply me with all rubbers except front and rear windows .. anybody know where i can find these seals ?? anybody that people on here have used before .. i am in NSW sydney area anbd would prefer to find somebody that will freight from other states or is in NSW .. Cheers Matt

Hey All If i said - Build me the Nasty'est 4K motor possible, what would u do to for-fill this request? (money isnt an issue in this lil game) (This requires every 1 to think excotic, but still possible) Lets here some ideas !!!

i have a cam for my 4ac, i got it a while back but I'm a little unsure what its like as i havnt had that much to do with single cam motors. i have not yet put it in (was waiting for a bigger carb so it would make a driffrence). the guy who i brought it from siad it was 290degree with an extra .6mm or .8mm of lift, its rated between 3500-7500. is this considered a big cam..? i know this is about the biggest you would want to go with a 4ag in a street car. i did a seach on you tube but i found conflicting clips with claimed 282degree cams, i sounded stock on idel and the other ideled like a stock one with the choke on. also because it has extra lift does that mean t…

Hi, Today I deided to go and get a new pump for my KE15 window washer so I can reinstall the water squirters. But the washer bottle I have for the water and pump, the hole in the bottem where the pump goes in for the water pick up the rubber gromet was perished and leaking and I need a new one. Does anyone know where I can get one? As I went to super cheap and they don't sell any. Cheers Cameron

Where is the best place in syd to get parts for a W58 box, i need some synchros and bearings.

Hey all, much to my dismay my 4AGE block has a pretty deep pit in cylinder 1, so its either get it resleeved or use another block. However, I have a spare 4AC. Is there anything stopping me from putting 4AGE internals in the 4AC block? Is it actually weaker or anything? My mate has also offered me a 4AFE in ok condition, read up about swapping the head and that seems like a no go. But same again, is this block suitable to receive a GE crank, pistons, rod assembly? Cheers.

hey guys I'm from the sunny coast i hv a black 2door ke30 rolla and i was wondering if a complete dash out of a 4door ke30 wld fit in my 2door? :evil: As my dash is jst about screwed. thanks bruce

hi all, just looking at buying a diff centre for my ke25 but i wouldn't have a clue what series it is eg: T , F

How do I determine what type my car is. The sticker on the engine is half ripped so all it says is 3K... The car is a 74' Coupe Deluxe if that helps... Cheers Tally EDIT: After reading the table on this page I think it might be just a 3K... lol single carb, silly me... http://www.superjamie.net/oldcorollas/engine/blocks.html

it amazed me a bit..all the sparks comes from 4 relocated coil packs.. the dizzy is left at place with no plug wires.. and it runs on webber carbs.. how did he do this..?? how it all wired up..?? :evil: