General Mechanical

Can anybody tell me anything about the 3k-h?? how was it different to the 3k-c? i have just got another corolla panelvan and it says it has a 3k-h.

OK so my car idles below 1grand (usually idles at 1grand) and putts along for like 10 seconds then a burst of normal idleing happens for a split second, then it idles bad again. Idles even worse after accelerating, stopped dead a few times and I ended up having to run with the choke out slightly. Putting along at walking speed when I parked it was doing small bursts of power too. Any suggestions? :n:

The diff in my KE70 has decided that is wants to shit itself (Not all the way shit itself but enough to not drive it incase it does break), I'm just wondering how much will it cost to buy a new or second hand one, it doesn't really matter if it is second hand because I will be getting a new diff with disk brakes just to upgrade them from shitty drums. So how much would a new diff be and to upgrade it to disks and how much would it cost to get a second hand diff, may have to get a new driveshaft because my cluth foot is kind of an itchy bugger, same as my throtle foot. Also is it bad when there is oil in the drive shaft tunnel just above where the driveshaft meet…

hi everyone ,thumbsup: looking for any info on a bigger axled diff to fit in a KE20 without going over track, hope fully handle 200+hp cheers on any info :

We have had a couple of problems since putting in the 7k and 5spd. The first one is last night Craig sheared the nuts off the tailshaft bolts. He swears he hasn't been loading it up. Has this happen to anyone else? The other problem is its started overheating. At first it took half an hour to get hot but over the week this has shortened to about 5 minutes. I won't get to see the car for a few days so any ideas would be apreciated.

Yes, thats right, I wanna know what the specs are for the engine timing. I don't see any specs in the FAQ, maybe it should be something that should be added and maybe also add how much advance you cang et out of the car to give it a bit more power? I'm running at 5 degrees BTDC but i reckon it could perform much better. Anyone got the specs?

can i have some help on finding a right size carby to upgrade to on my 4k engine

As the topic suggests, i can't get enough travel with the clutch system for my hydraulic clutch conversion to allow me to change gears or even get it into gear. What has everyone else done about this??

hiy guys as you may know i resently did a 4k-c to a 4a-c conversion. all went well however i have a carby that takes two wires and i only have one wire connected coz i don't know where the other one goes help... where does it go. i know the engine has auto choke but the alternater has nothing marked "W" which i was told it whould be connected to. anyhelp for where it connect by the way its red. Cheers by the way it is idling a bit high as well.

Hey My Ae92 Seca has a rear brake prob, The pads and that are pretty new but the rear brakes barley work. The handbrake is a bit soft as well. Is the anything in the drums that you can adjust cos when you plant the brakes it nose dives :P

OMG ! Where do i get one ! :P !!!

I don't know a whole lot about the 1K head and I've been offered a fairly worked one by a workmate. Yet to actually see it so I can't say about whats been done to it. I'm pretty sure they fit onto 5K blocks? If so would there be a gain from this or just a waste of time... or actually kill power? Either way I'll be making some form of meaty K-motor over my holidays coming up, just tossing around some ideas until then. Cheers.

Was sitting in front of my car yesterday while the tailshaft loop was being finished off, and looking at my bumper. At the moment, my oil cooler sits in the gap above the front spoiler: This all seemed like a great place to put it: Well... until the bumper went on: *doh* Anyway, so there I was sitting there, and I thought maybe if I drill some holes in the bumper, I'll get more airflow to the oil cooler. Is it even legal to drill holes in your bumper? And then I realised another thing, I can't really even drill many holes in the bumper, because the numberplate is in the way... Maybe I can move the numberplate too? I think th…

Was speaking to the fabricator today and looking at all his Speedway bits (he does speedway), and got to talking about how much it would cost to make a manifold to bolt on 20v 4AGE quad throttle bodies. Or to get a set of his custom made slide throttles... Anyways, no real figures were discussed as he needed to think about it, but he did suggest something that apparently is quite common among the V8 boys, which he recons would be easier and cheaper to set up, esp considering how much the 20v quad throttle bodies actually go for. His suggestion was to make a pair of plenums, and get another standard throttle body (or off some other car, apparently the Ford Falcon …

I have a really anoying LOUD knocking noise from the front left hand wheel and knocks when you turn to the right. CLUNK CLUNK CLUNK CLUNK, and you can feel it through the whole car!. Driveshafts are pretty new and I have just replaced the wheel bearing on that side and the boots and re-greased the CV joints. any ideas??

I have an AE82 its stock bar the spottie on it the issue i have is that its hard to start and i wanted to find out why i plave another battery out of my rover (Mower) in it its a fair size its still 12 volt though and it started it the other day but i went to start it yesterday and it wouldn't start it turned over once and then stopped. The lights on the dash the oil etc went out and wouldn't come back on so i put the old battery back into it just wondering if anyone has any idea on what was/is wrong with the little beast. By the way in the way of spotties there is aprox 450 -500 watts of lights on the front. Sorry bout the long post.

Don't know whether any of you guys know of, or have used the following site before. AUTOSHOP101 I came across it recently, while researching how different electonic engine management systems solve the problem of exacting timing during cranking. The site is very informative. It has basic information and some very interesting technical articals on lots of interesting automotive control subjects. The technical articals are fairly generic, but are all based on TOYOTA technology, so most things you read on the site are very applicable to our engines. I recommend the site as a good read to any "newbies" who read these pages but are too frightened to ask, b…

Hey Group, I just bought a 69 KE15 sprinter to play with. It is in pretty good shape and I'm trying to build it to run autox. The k motor is in fair shape needing minor tune-up and carb rebuild. I found a 3k that had been rebuilt recently with a new clutch and good looking carb with all components attached. The plan is to drop the 3k in and try to get as much out of it for as little $$ as possible. Is there any benefit to using the k head on the 3k block or will everything stay the same compression wise. I plan on trying to get the head ported as well with either of the two. Maybe try it myself on the k head and see if I can manage to make it work. Any suggest…

Hey, as i mentioned once before, my mate just brought a 1999 toyota seca and he decided that he wants to be more quicker, or GONE as he states it! Ive googled it and the best possible solution is that the toyota starlet turbo engine should bolt up fairly easy....... but he doesnt want to lose displacement..... He really love a 4age turbo but its guna cost him.. Does anyone know of anyone else who has done any upgrades to one of these models?? I'm sure it would be alot of messing around to get it turbo charged - roughly $10k... Thanks :D

right i have a ke20 rolla and ive swapped the original moter and tranny for a 5 k and 5 speed manual from a ke70 rolla and I'm not getting any economy on the highway. 3500 rpm at 100 ks an hour so i was just wondering what diff ratios were offered from the factory and if anyone knows of any for sale or anything else that could be suitable

I have heard about a 4.1 banjo diff does any one know if it is true?

Has anyone ever had to replace one of these? I've been told that AE86 uni joints are non-serviceable items, so the entire yoke etc has to be replaced, or the old uni machined out (both of which = lots of money)? I've got a strange vibration in the car since the incident that I'm still trying to pin point, it's speed related, so I'm guessing it'll be wheels, diff, tailshaft, or something in between. I've gotten the wheels rebalanced, so that *shouldn't* be it. I keep having nightmares of my tailshaft letting go, and considering I don't have a tailshaft loop that could get quite unpleasant quite quickly. I'm going to replace all the tailshaft bolts just for peace of…

Ok so your 4K-C cuts out at idle and you are about to mess around with the carb. First make sure this is plugged in: Oh wtf a loose plug. Oh there we go. Car now idles perfectly. Hope this saves someone some trouble

will these fit a ke25 properly with the correct offset?

Ive been here for... what.. too long now, and ive gotten to know most of you pretty dam well. Somethings have caught my ears and eyes latelly.. well not so much latelly, but here goes anway. Most of us here, the regulars, have corollas - new / old / stock / not stock / rusty / K powered.. what ever it may be. Do you own a corolla becase you like them? because you can't afford anything else? because of toyota's reliability?.. and why do you like your corolla? I like my ke70, because of its unique shape, its reliable factor, the ability to get new parts for it.. well.. most of the time, its simialiries with the drifto Ae86 parts.. etc. Edit by me -> its R…

hi i was just wondering how many splines there are in a ke55 diff axel!!!

hey guys my speedo says i'm doin 50 but aparently (acording to other drivers) i'm only doing 40, it has the original size rims 12's ans tyres (i think) 'sr12 155's' does anyone know why this could be out? and how or where it can be fixed? thanks P.s its a 4 spt manual

Hey, I have a Ke25 with a 4K. I have recently found an oil leak after having none for the last 15-20 years (its been in the family since almost new), It seems to be coming from around the headgasket area! i have cleaned it up tonight and topped up the oil for further inspection 2 moro after a drive to see if i can see where it is coming from. I'm guessing its not the headgasket cos i'm not burning oil etc. I was wondering if anyone knows of somewhere they commonly leak in the 4K? i'm hoping to fix it myself (apprentice Mechanic for a holden dealer), mayb if big work time for upgrades! thanks!

guys about a week ago I noticed my corolla was down on power and there was some exhaust fumes gettnig in the car, but not too bad at that stage. Only a few days before this I had ran the tank almost dry, and the car seemed to have definate flat spots in the power so I figured the reason for the loss in power was because the carby was blocked with shit. replaced all fuel lines and filter and cleaned the jets in the carby. Flat spots were definately gone but car still felt noticebly down in power and exhaust fumes were getting worse. I figured the muffler was blocked as I had just noticed the exhaust sounded different but thought I was imagining it till this point. Anywa…

thinking of putting AE86 springs in bubba (TE72) did a search, found a good topic, but it stalled before the question was answered the springs are huge!!, close to 5" around do you guys think they will fit?

the 2zz-ge engine would have to be the most recent engine to be put into the corollas that we all now and love. Does anyone know anyone that knows them inside out ??? I've been chasing someone in brisbane or anywhere in AUS that can talk to me about them. As I have basically come to the lengths as far as bolt on mods goes for my rolla so now its down to internals. or anything else that we can think of. Any info would be great thx guys :P

Can anyone please help me? Ive been searching all over thenet and can't find anything.... I need the performance stats for; - 1990 toyota corolla w/ 4AC 1.6L & - 1999 toyota corolla w/ 4AFE ??? 1.6L Thanks...... :)

This is the idea I saw a while back Jamie..

does anyone know what size ring gear is on a 4.1 ratio salsbury out of a ke55 sedan?

Did a search but can't remember whether it was on this site or another that I read this advice. Someone suggested using a screwdriver shaft on a drill to prelubricate the bearings before a first start, after an engine strip down/rebuild. With dizzy removed the oil pump is not connected to running gear, so can be turned by poking said apparatus down dizzy hole. Never tried this before so gave it a go at the weekend, on 5K just about finished. Lubricated the bottom end OK, but couldn't see any oil coming out around the rockers. Occurred to me that upper head lubrication maybe from a flat on the camshaft journal as I have come across in other engines I have w…

Crash Course in Seam Welding. All you need to know to start welding :) I decided to write this because of the lack of good, detailed documents on line on how to weld. The only experience was about 1 day of stick welding. Which no one taught me how to use. This time I got some help by a professional boiler maker. So I'm passing it on to help 1st time welders. The first part will go through removing rust out of panels and prepping it for welding. This should get you to the stage were you can fill over the panels with bog. Things you will need. • MIG welder • Welding mask if you don't want eye sunburn. Yes it hurts. • Tin snips. • Sheet metal. I…

as I'm looking to purchase a stock version of one of these but don't no a hell of alot about them, i would really like to know what i should look out for when looking at these, also stuff that can go wrong and general info that may be of some help cheers the drfit king...

Hey all, finished moving my leaf springs in 10mm today, a friend has changed the offset of some 14x7 ra40 celica rims and tacked them together so i can trial fit. It took a bit of messing around but i finally have them in place. Slick are 24.5 x 8 x 14, the buldge is the widest part at 258 mm wide, i should be able to get a 255 street tyre on the rear now too :D I have about 3 mm clearance to the leaf springs now, do you think i should change the offset by 4mm more and slightly scallop the springs? i am un decided of whether they still stick out to far? as it sits i should be able to roll the lips and not get any tire scrub, opinions please? last thing i want is a car…

bummer, i reversed out my mates driveway, and left onto the road, and hit a bullbar sticking out off a 4wd that was parked on the footpath at about 30km/h. was pitch black, and i was obviously not looking properly. the rear left panel is warped, the boot wont close, the tailight is in the boot, and the bumper is still straight. the tailight area looks like an eye socket. might just get another Ke70, and use this one for parts.

Hello all, Could some body please scan and e-mail me the rebuild procedure + pix for the carby off my ke20, My carby kit is not the right one and it fell apart when i pull the two main bolts out of it... so i am ...... without help..... thanks :P