Engine Conversions
Toyota Engine conversions - Q & A
1441 topics in this forum
-
When upgrading your engine or even just putting something in of same or potentially less power you need an engineers certificate. So how does this process work and what does it cost here in Victoria. What are your experiences, both positive and negative. Can you dispelled any myths and promote this course of action for some of us. Example. Corolla on eBay didn't sell for 18K had an engineers cert and a v8.
-
- 16 replies
- 362.1k views
-
-
Hello Long story short. My 87 GTS Coupe is falling apart, the chassis is slowly deteriorating and unable to be restored, I found an 86 coupe GTS chassis, and will swap everything over. I've done relatively big jobs on my own before and feel as though i can tackle this. My motor is rebuilt with about 12,000 miles on it, new clutch/flywheel, rebuilt rear end (4.778 R&P, 2 way lsd, diff rebuild kit, axle bearings & seals, driveshaft center support bearing) I need to obviously swap everything over, and it should be relatively easy being as that i'm swapping it into a GTS. I know i should keep track of EVERY nut&bolt, label them and put em into plastic baggies…
-
- 3 replies
- 383k views
-
-
Hey guys, I'm new to the forum. Thought I would post up how I'm tracking with my wee project and hopefully get a few tips along the way!! Current stage: Engines/gearbox in, diffs in, wirings complete, yeah engine runs!! Suspensions in, fuel systems in and she's all painted. Currently working on brakes and wheels then finally exhaust to finish up. The engines out of a S15 silvia with the R32 turbo box with sr20 bellhousing. Diffs out of the nissan pintara, shortened and bolted in (only brake lines and handbrake to mount up). Front brakes I have gone with the U13 bluebird front rotors and rx7 s4 callipers. Having trouble finding wheels that will fit with e…
-
- 48 replies
- 536.3k views
-
-
Hi All, I drive a beautiful 1975 KE30 2door, running dedicated LPG on the stock motor with a 5speed K50 transmission. Car is a dream and a keeper, bought from a rolla club member Dale AKA doityourself on rollaclub. I have been driving the rolla for a few years now with no problems, runs beautifully and usually won't give me much starting trouble even on cold winter mornings, really reliable and well taken care of car. The praise should go to Dale (doityourself) for his beautiful work on the LPG conversion, custom exhaust and a lot more tlc. After a while the little engine can be a bit tedious and sometimes you itch for a little more excitement and oomf to ma…
-
- 16 replies
- 524.3k views
- 1 follower
-
-
Looking at doing a 7age swap in the future, most likely a silvertop 20V Now, I already have a 7afe, in my AE112, what do I need to make it the 7age. research here says adjustable cam gears, a fancy timing belt with 1 extra tooth, and the 4A pistons. First off, why do it need the 4A pistons, that's kinda annoying for me as I don't really want to muck around with the block too much, but if its necessary then I guess I'll do it. What else is needed for this to work, what special things do I need fabricated and what can I get away with keeping standard. Also, wiring, my stock car is OBDI, I'm guessing the silvertop is OBDII because of the VVT, so would the s…
-
- 0 replies
- 296.5k views
-
-
Hey guys ive been reading through all the forums loking at all your engine swaps, I love my ke55 but the motor has shat it self bent 2 rods and snapped 1 would It be better to rebuild the top end and where do I get the parts if so ? Also would it be better to replace the motor if so what is the best and cheapest ? TIA
-
- 6 replies
- 284.4k views
-
-
I've finally started on my partners KE10. Previsously was running a worked 5K big cam, twin webbers, lots of head work etc. Now shes wants more power so its time for a ground up restoration. I'm starting by doing a full mock up first. Any way heres some pics let me know what you all think. :D
-
- 15 replies
- 61.8k views
-
-
I am considering this as these engines are abundant here. I can get the NA and supercharged ones from junk yards. Problem I have is that they are all FWD. I may be able to bolt a t5 camaro trans to it, but It wont hold the HP that the Supercharged engine produces. Anyone know of any Buick, GM, or holden swapped engine builds?
-
- 3 replies
- 235.5k views
-
-
Hello You guys might have seen me asking around for a K50 box to ship to the netherlands, but ultimately I decided that it just wouldn't be worth the trouble, and I'd be better of just going big, So I have decided it is time I perform my first engine swap (with help) As far as the car goes, I've got a KE35 with just the stock 3K-H and K40 gearbox, but because I just want to be able to get along with the traffic, and have a bit more fun, and because I just want to take on such a project, I quickly landed at the 2T-B paired with a T50 gearbox, these are (unlike the K50) quite common here because the celica did arrive in great numbers, 2T-G and 4AGE are o…
-
- 25 replies
- 414.2k views
-
-
Hey guys i want to put a sr20det into my ke30, just wondering how much modification will be needed to fit the sr20, and any advice will be great, like driveline, and suspenion n all that, thanksss
-
-
- 2 replies
- 300.6k views
-
-
Hey guys, I'm about to purchase a blacktop 4age for my corolla in replace of a 7K. To my understanding i know i haven't though about all the little things that would have to be done to make this work. I have someone that will be installing the engine with me, but has asked me to make sure i have sourced all the right parts for the RWD conversion. Looking at all the ke-7* or Ae Conversions there has been alot of things that i haven't though about ... eg peddle box. so could someone that had done a similar conversion or has appropriate knowledge help me in understanding the full procedure of this. engine: 4age blacktop Box, T5O tailshaft options ??? no idea…
-
- 8 replies
- 127.6k views
- 1 follower
-
-
Hi Guys My car is a JDM AE 101 FX this car has been a project build for a few years and after reading snapz build I decided to post mine to also help others along. At present it sits a pile of parts waiting to be assembled but being unemployed at present the car is taking the back seat. Engine is an AE 101 4A GZE hybrid crank is from an AE 101 4A FE Here is the list of parts and what has been done so far Head has been port and polished and matched flowed, low friction valve guides have been added and also 1mm over stainless steel oversized valves. Cams will be Colt cams tri flow cam shaft OEM valve springs and HKS retainers Block is awaitin…
-
-
- 7 replies
- 99.1k views
-
-
Hey guys, So if i were to purchase a Bigport 4age engine that would be coming straight out of a JDM AE86, (The AE71 has a T50 gearbox and the engine would come with the stock ecu and loom) Would the 4age literally just go straight into the AE71 with no extra costs?
-
- 7 replies
- 415.2k views
-
-
Hello! I am new to the world of Toyota's and I have some questions. What I have: I just bought a unfinished Locost 7 with a USDM 1982? Corolla engine and transmission. The engine is need of a rebuild and has Honda Prelude carbs on it. I have been using the search to find out what I need to put a 4A-GE Blk top into my "new" car. My car has a T-50 with hydro clutch master in it. What clutch & flywheel, clutch fork ect will I need to get for use with the 4A-GE Black Top? Sorry if this question has been asked 5000 times, I could not find the grocery list I was hoping for searchin' :-) Is there a specific Meth Injection kit for a 4A-G…
-
-
- 13 replies
- 40.4k views
-
-
Hi all Looking to do a 2t conversion in me KE55 soon Was just wondering what the go would be with legality of the swap in SA? As it was in the TE5# would it just be a matter of changing the engine number or would it be required to go over regency? Cheers Todd
-
- 17 replies
- 467.1k views
-
-
hey this is my build progress on my ke30 project UPDATED 7-12-2014 so many more pics of the new look on page 8 :) Engine: forged and built SR20DET (s13)Turbo: Garret T3071r , HKS step 1 cams 256, rocker arm stoppers steam pipe top mount manifold, custom radiator with thermo and custom intercooler all alloy piping, turbosmart external wastegate (plumbed back) Fuel: (changing fuel pump soon) nismo 740cc injectors 8mm fuel lines Computer: AEM Exhaust: 2 1/2 inch pipe into highflow cat and into a highflow muffler with dump tip Diff & rear brakes & suspension : Hilux LSD 4.11 ratio with 285mm el falcon disc set up. with s13 rear calipers custom ta…
-
- 120 replies
- 225.3k views
-
-
- 1UZ
- TE38
- Engine Swap
- V8
-
Tagged with:
I want the most badass, ratty rat rod corolla wagon ever. Do you think I could fit a 1uz in my 1979 Corolla wagon? I know a jz wouldn't fit, it's too long, but a 1uz is shorter right? I may be crazy but...yeah no I'm crazy.. Help me complete my dreams. Haters will be ignored.
-
- 18 replies
- 651.8k views
- 1 follower
-
Hi guys, Plenty of awesome engine conversions here. I decided to detail how going from 4agze to 4agzte went in my case - maybe it will encourage somebody to go this way too (or opposite ;-)). Got plenty of pics from this build - will try to document all when time allows. This topic will contain only materials related with twincharging - more pics and vids regarding my rolla can be found in this topic (http://www.rollaclub.com/board/topic/63701-ae82-twincharged-corolla-sznaps/) where i put in general all updates of my twinky. The system is completed and in use for over a year now. Mostly street use but been on couple of track days and I must say I am completely…
-
- 55 replies
- 577.7k views
- 1 follower
-
-
Hello, I am wanting to do an engine conversion of my '78 KE50 Liftback Delxue. I have no idea, literally\ She's slow as f*ck. Personally I love turbos, but as I said , I have no idea Thaaannkssss =]x
-
-
- 10 replies
- 612.6k views
-
-
hello, I am going to buy my friend's KE30. it is 4 door. I am planning to replace the engine & gearbox (the original only have 4speed). the question is: 1. is it possible to get a 5AFE engine?? 2. what is the easiest & the simplest injection engine to attached?? 3. are there any kind of gearbox that can be use without any customization?? my friends said that the best engine to be attached is 4AGE, but for me it is too expensive & for my opinion it is a thristy engine. I like a so so engine, that have a bigger power than the old one but not much and I like the injection one. sorry for bad english thx Rolla Club
-
-
- 24 replies
- 208.4k views
-
-
just would like a bit more power in my ke10 rolla and wondering if a 1.6 4ac would fit?
-
- 9 replies
- 258.7k views
- 1 follower
-
-
I've Got a 2tg in my ke70 it leaks a bit of oil fun little motor but I'm just not sure if it's going to be reliable and cost effective for the power I want if I turbo it, on the plus side it's already in the car but it wasn't the best conversion I bought it done and the cross member looks dodgy as hell and I'll need to find an injection system and ecu which will be hard go find. Second Option Would Be a 4agte I've Just Stripped an Ae71 so I've Got everything except the engine But I'm Just Not Sure If It Will Be Reliable Once It's boosted finally There's the sr20det I've Got Nothing Besides A z32 Afm but The Motor Makes Good power stock So That Would Make It Reliable
-
-
- 16 replies
- 207.2k views
-
-
Hey peeps. ..I installed the 3sgte into my ae101 corolla fx and had modified the 20 valve harness to work on that engine while running an aftermarket ecu. Currently I have installed the patent 3sgte harness and ecu but there are two connectors that are on the harness both grey and black that are close to the ecu connectors that I would like to wire in....anyone having any wiring diagrams that could assist me?
-
- 2 replies
- 89.5k views
-
-
Hey Guys, currently in the middle of putting a CA in my AE71.. it has S13 front brakes and R31 rear brakes, I'm thinking i might need to upgrade the booster and master cylinder but really no idea where to start looking into what i should be using. i have found already on the forum something about N14 pulsar booster and pajero master cyl but I'm not sure if this applies to what I'm doing.. any info would be much appreciated. Thanks
-
- 0 replies
- 485.8k views
-
-
I will be swapping this: into this: I will document each step as I go along. The firewall has been notched 4" and the section has been boxed: The original shifter has also been relocated to suit the R154 The car is plauged with a little rust so progress will be slow. Before: After: Plans include: rear-mounted radiator 3" SS exhaust 8.8 rear 4 link T70 turbo 30 x 12 x 3 I/C mounted behind grill expansion tank modified oilpan custom catch can shaved bay bigger injectors (not decided which yet) aftermarket ecu (not decided which yet) fuel cell ans external F/P swirl pot All welding and fabrication will be done by me. My inspi…
-
- 15 replies
- 333.3k views
-
-
Hey I need to no befor I buy what do I need to change to put a 4k in my ke30 Can I use the 3k gear box on 4k motor And are all of the wires the same So what do I need to change ??
-
- 2 replies
- 451.4k views
-
-
Hey just after any advice on where I can get a hydraulic clutch for a ke30 for my ca project and any other advice anyone has to do with this convertion. I already have the motor and box and I have ordered the engine mounts. And if anyone knows a good engineer in the Liverpool/Sydney area. Thanks in advance
-
- 4 replies
- 277.1k views
-
-
4 age conversion or just build up 4k? i don't want too much power, but i would like to know what people are getting out of their 4k engines. and are there better ways to go than 4age?
-
- 10 replies
- 172.2k views
-
-
Need some guidence from some people that have already done sinething similar (want to do it right the first time if I can hah) If anyone could link some similar build threads or throw some ideas my way that would be great My ideas so far are either a: 20v + twin turbo 16v ze + twin or pos. Just single R31 front end RX3 rear? Or hilux because its easier and cheaper I'm located in western suburbs Vic so some shops that might be able to help me out with turbo choice and and ECU set up. Thanks in advance for any help guys!
-
- 19 replies
- 282.9k views
-
-
wanna do up a 4k engine N/A any ideas? wondering how the 3k heads hold up and the difference in the compression?
-
- 8 replies
- 236.1k views
-
-
Hey all! Looking at doing an 18rg engine swap in my corona as my old 18rc is on its last living days. Was just wondering if anybody could give me a list of the parts ill need for the 18rg swap that my 18rc engine can't already donor for, Most parts i guess will be interchangable, radiator, fuel pump, dizzy etc ? The car will just be used as a daily/ weekend car, so I'm not looking at serious mods at the moment. Hopefully want to get it as factory spec as i can. There must be somebody who has done this conversion before and has an indepth view of the best way to go about it. Just want to add up a rough price for the parts ill need and make a plan. che…
-
- 3 replies
- 111.2k views
-
-
Hey guys just after some info on doing engine swap, I want to know what is the best engine around 2L from a toyota that will be more or less a straight drop in?
-
- 7 replies
- 221.6k views
-
-
hi all i have a old 3k motor and I'm wondering what i will need to do to put the 3k head onto a 4k motor. i heard it goes allright just wondering what to do. is it as simple as just bolting the 3k head to a 4k or is their more involved any help would be great cheers :)
-
- 14 replies
- 47k views
-
-
I'm convetingy ke30 4 door from a 4k to 4afe and i need some help finding the right parts that will fit into it will very small mods 1. what mounts will i need 2. what gearbox will i need 3. pretty much every ill need to conver it
-
- 2 replies
- 199k views
-
-
Hey guys, Picking up a new ke10 rolla project in the morning which is same old unfinished project story. Solid body resprayed and no rust so great base. Now it doesnt have a drive train so i was looking for a good 4 or 5 k base to drop in there (my understanding is pretty much no mods required to do this yes?) I was going to pair either of these with a k50 to get it on the rosd and cruising as quick as possible so i don't end up leaving it to sit for too long. If anyone has either engine (hopefully around brissy) please let me know. Also any advice or tips from experience with this install would be awesome. Cheers
-
- 5 replies
- 132.3k views
-
-
Hi guys I have a 79 corolla ke55 which is auto. After using it as a daily driver for the past 10 years with the stock 4k engine, I have now decided for bit more power and thus a efi engine. Now if you guys please help me in selecting a good engine and gearbox for my car, that would be greatly appreciated. I am not after too much horse pwer , anything above 75kw I am happy with. I want to keep the car auto. If you or a friend/shop does this type of work, I am more than happy to pay you to do the job. Thanks and kind regards
-
- 12 replies
- 146.7k views
-
-
Hi Recently purchased an auto 79 ke55 and overhauled the carby. The car is so slow, I want to keep the car auto but want more power from it. I might consider an engine conversion if someone is willing to do it for me for under 4k, unfortunately the car has to be auto because me and the gf share it and she does not want to drive manual. Any other ideas beside engine conversion ? I have zero technical skills and am a noob, but I have been in love with old coronas and the ke55 since the past 10 years and took so long to convince my gf to allow me to buy this car for use by both of us. location: Sydney Thanks
-
- 5 replies
- 268.1k views
-
-
Hi after puttin in a smallport 100kw into my coupe I'm a fitter welder and own a workshop can do all myself but just after some advice on mounts and crossmembers can I use ae71 engine and gearbox x member as direct bolt up or is this a false claim? Does anyone have a sketch if so of mounts and x member if custom ? Best to use t50 box? And is there a bolt up tailshaft or again a cut and shut job any info appreciated cheers nath.
-
- 2 replies
- 102.2k views
-
-
I have a 1974 rt81 and I got a 3rz engine I won't to put in my corona but the 3rz is to tall das any one have pointers to help me thank you
-
- 2 replies
- 90.4k views
-
-
hi all i am wondering if any one has done this or if any 1 have some links to information on doing this as i have found an engine to use with only 50000kms on the clock and i really would like to have this set up not sure if is any way possible but any help would be greatly appreciated and still use the orginal gearbox centre lock diff system
-
- 0 replies
- 76.4k views
-